Shopping Cart

Your cart is empty.

Your cart is empty.

FAN 50 PLUS PINS Universal Ignitor Board with Fan Control for 12V DC Furance Fit for Suburban/Atwood/HydroFlame Furances

5.0 Write Review
Free shipping on orders over $29.99

$48.99

$ 23 .99 $23.99

In Stock
  • 【Perfect Compatibility】This FAN 50 PLUS PINS only fit for 12V DC Furances, designed to compatible with Suburban/Atwood/HydroFlame Furances. Compatible with Atwood Hydro Flame Furnaces: 7912-II, 7916-II, 7920-II, 8012-II, FA 79D, HF 80D, DC82 25-32, DC82 35-41, FA 76D, FA 78 25-32, FA 72D, 8500-IV Series, 8500-III Series, 85-II Series, 85-I Series, 8900-I DC Series, 8900-II DC Series, 8900-III DC Series, AFSD12, AFSD16, AFSD20, AFMD20, AFMD25, AFMD30, AFMD35, DFMD20111, DFMD25111, DFMD30111, DFMD35111 DFSD12111, DFSD16111 and DFSD20111.
  • 【Perfect Compatibility】Replacement for Atwood and Suburban Control Boards: 31501 Kit with 33488, 37875, 36716, 232613, 232614, 520820 Kit with 232613. This FAN 50 PLUS PINS maintains backward compatibility with Fan 50 Plus and UIB fan control boards that have been available since 1994. Does not fit for DuoTherm 900 series furnaces or any other furnace with a thermostat in a grounded circuit.
  • 【Upgrade Design】The Fan 50 Plus Pins Ignitor Board can be used to upgrade older furnaces to add the Fan Control feature. It is designed to work with the industry standard 6-pin “edge connector” or the newer 6-pin “header” style connector to address changes in the industry while maintaining backwards compatibility.
  • 【Safe and Effective Work】The Fan Ignitor Board is used to turn off the fan motor if the board fails to sense a flame after the third ignition attempt. Favorably reduces battery consumption and eliminates unwanted cold air blowing. After turning off the fan motor, the board will wait 1 hour and repeat the entire sequence again before turning off permanently.
  • 【Reliable Quality】Made of premium PCB material for durability and good compatbility. Professional manufacture technology, help upgrade the function of your furnance.
  • 【Easy to Replace】The Fan Ignitor Board comes with a “removable” MODE SELECT jumper on the board and a separate set of red and orange wires to convert “older furnaces”, giving them fan control features. Please note: The “fan control feature” must be used. Installation manual included, easy to replace. Consulting Professionlal technician is recommended while replacing.


johntruck Replace for FAN 50 Universal Ignitor Board with Fan Control For 12 VDC Furnaces. Designed to compatible with Suburban/Atwood/HydroFlame Furances. Compatible with Atwood Hydro Flame Furnaces: 7912-II, 7916-II, 7920-II, 8012-II, FA 79D, HF 80D, DC82 25-32, DC82 35-41, FA 76D, FA 78 25-32, FA 72D, 8500-IV Series, 8500-III Series, 85-II Series, 85-I Series, 8900-I DC Series, 8900-II DC Series, 8900-III DC Series, AFSD12, AFSD16, AFSD20, AFMD20, AFMD25, AFMD30, AFMD35, DFMD20111, DFMD25111, DFMD30111, DFMD35111 DFSD12111, DFSD16111 and DFSD20111. Replacement for Atwood and Suburban Control Boards: 31501 Kit with 33488, 37875, 36716, 232613, 232614, 520820 Kit with 232613.