Your cart is empty.
Your cart is empty. Wire Cross section:0.08~4.0mm²(solid), 0.08~4mm²(stranded)
Rated Voltage: 250V/600V
Rated Current: 32A
Shell Material: Germany Bayer flame retardant PC
Internal Material: USA DuPont PA
Guide Strip: Electrolytic copper (Surface tin plating)
Spring: Nickel chromium alloy steel
Product Size: 39(L)*13.4(W)*14.5(H)mm
How to use our products:
First Step
Strip the wire according to the specified length.
Second Step
Dismantle the orange operation handle straight and plug the wire into the hole.
Third Sted
lower the handle.
Problems in our lives:
Because the electrical tape, the wiring cap and other connections are prone to aging,
falling off, poor insulation performance, etc., the safety hazard is formed, which may
cause personal injury such as electric shock or a short circuit of the wire to cause a
fire. In addition, as the use of home appliances increases, the power load increases, such
as poor contact at the wire connection (excessive resistance at the connection), and large
resistance and large current cause heat increase, which will be a huge safety hazard.
The XHF connector completely avoids the above-mentioned safety hazards caused by poor
connection; our connector uses ROHS-compliant materials and is environmentally friendly;
UL Certification.the shell is made of flame-retardant transparent PC, nylon PA66, and the conductor is
tinned with pure copper. Small, low electrical loss, imported stainless steel circlip, and durable, reusable.
Chuck Miller
2025-09-02 15:34:21
I got this to splice jumper clamps on my battery charger which came with some weird ass connector that was a pain to put on and take off.Now I have normal, standard jumper cable clips to connect my charger.Very solid, meet all the local electrical codes, quick and easy. Just cut the wire, strip off 3/4 inch, insert and clamp down. Done. Not worried about stress or pulling out.I used one like this with 3 slots to add a new outlet to an existing line that only had a couple inches of play, so didn't have room or slack in the wire to use wire nuts to splice in a new wire.So cut original wire (one black, 1 white, 1 green).Need 3 of these splicers, each with 3 inserts.Inside an electrical box (I used a thin / flat one).One block for all the black wires: - Put original black wire source into slot 1 & clamp down. Put original other end of same black wire in 2nd slot and clamp down, add 3rd black wire for new outlet into 3rd slot and clamp down. Now all black wires are bound together. - Do same for all 3 white wires (all 3 in one three-slot junction box) - Do same for all 3 green / ground wires.Presto, instant new wire to run to new outlet I was installing in ceiling of porch for camera.
vdawg
2025-08-19 16:28:14
I've had a chance to use these on a couple of low-voltage applications where I had a two-wire splice connection between a power source/transformer and a device that I didn't want to be permanent and they work well. The clamps are very strong and hold the wire firmly; even very thin 20 gauge wires.
David S.
2025-07-26 17:24:27
These are so much easier to use and reuse!
NoName
2025-07-25 18:57:34
Hard to open and close. You have to open it by raising the levers before inserting the ends of the wire and then lowering the levers to close it. Don’t use these connectors with very thin wire (24 gauge) since they will break the wire.Two of the 10 connectors actually broke when I was using them. On one, the lever broke off when I was opening it, and on another, when I closed it on a 24 gauge wire, the wire broke off inside of the connector and then the connector would not open after that. The rest of them worked, though I only used them each to make one connection and I can’t vouch for their ability to open/close repeatedly.
John F Hall
2025-07-08 12:08:59
I've been replacing the old incandescent light fixtures in my house with new LED fixtures and these little connectors have saved me a ton of time! No tools needed and they just work. Perfect for ground/neutral/hot connections.
Captain
2025-07-05 16:29:27
Good value for the money
Randy Stanard
2025-04-20 15:02:18
I initially purchased this lever wire nut because I had an application where a bracket to hold the wire nut was helpful. These did not disappoint. The bracket does solidly hold the lever wire nut in place.These lever wire nuts seem to be quality constructed and grab the conductor making a reliable connection. Once the lever is closed, wires cannot be removed (unless you release the lever). It grabs wires very solidly and makes a reliable connection. I would trust these lever wire nuts to join wires for long term service.The only CON for this product is that the levers are NOT color coded. If you read the description carefully, you'll see that these lever wire nuts are configured for TWO inline circuits. These lever wire nuts do NOT tie all four conductors together. Each of two inline circuits are tied together. Because all levers are orange, you might believe that you can connect 4 wires together as you might with tradtional wire nuts, but this is NOT true. What you have are two separate circuits inside this wire nut, so you could connect together a pair of two-wire cables.Other that this one CON, these are very good wire nuts that when deployed, should last FOREVER. I recommend this product.
John Menard
2025-04-15 16:28:25
Just like the expensive ones from the electrical supply house.
ali
2025-03-15 10:27:08
ممتازه
Customer
2025-02-21 16:44:00
easy to use
faisal
2025-02-19 15:54:22
مقارنه بالأسعار ÙÙŠ المØلات Ùرق Ù„ØµØ§Ù„Ø Ø£Ù…Ø§Ø²ÙˆÙ†Ø§Ù„Ø¬ÙˆØ¯Ù‡ ممتازةوسهل الاستخدام
Khaled
2025-02-01 10:36:15
ممتازه
Ayman
2025-01-24 14:24:15
جيد
Recommended Products
