Your cart is empty.
Your cart is empty.Product Description
Hello
2025-09-04 17:09:44
They definitely fit the TR50, these just require a harder push when loading it’s not the soft ball so it’s not gonna just fit right in, and I definitely won’t say it didn’t hurt my fingers a bit loading these especially because after loading the soft silicone balls so easily the need for a tough grip and a little strength to put these in was a bit surprising as soon as I loaded it I went to take a shot at first I thought it was jammed but I also had to pull the trigger with a bit more force as well and as soon as I did I shot a hole right through a bucket 🪣 I won’t be able to use it for mop water or water balloons anymore but at least I know it works, the shot is powerful and I have no regrets. Good Buy!
Kidd Kool Arrow
2025-08-29 11:38:51
ATTENTION! These .50 steel bearings DO Fit! For those that think they do not, just do not know how to load and break in this less than lethal self-defense pistol. It is certainly not a "BB" or airsoft gun. They are most certainly 12.7mm. polished, straight and precise with no defects, flats, pits, soft spots, or cuts. Install rounds ONLY from the front octagon barrel side of the magazine cylinder. For a new unused magazine push one round first into AND out a few times of each of the cylinder holes from THIS SIDE so the magazine will continue to retain them afterwards, for nylon is much harder than plastic and rubber, and this is what these guns are made of and must be broken in properly. Then fill the magazine with rounds from THIS SIDE of the barrel magazine NEVER from the star valve side. Thank you PGN Bearings for the excellent .50cal ammo.
Alec Wade
2025-07-11 18:58:14
They slang slung shot.
Hambone
2025-06-30 15:01:40
Good easy to use ammo for critters and or target 🎯 practice
Sarah L.
2025-06-19 18:29:26
These rounds were purchased to use as ammo in my HDR 50. They did not fit well in the chamber, and they did not fit through a tuning barrel either. My stock HDP 50 can shoot them just fine. They come out fairly slowly unless you upgrade the firing pin and do a valve-block delete. You will still get about 15 shots per CO2 cylinder, which is enough for me if you make these modifications.Overall, the bearings are very consistent in size and easy to shoot. They weigh in at 8.32 grams each.
Felipe Garcia
2025-06-05 14:01:21
These bad boys definitely fit in my HDR50 magazines . They are slapping hard and powerful. Takes a bit of effort to fit inside the magazine but they definitely work. Definitely recommend these for the HDR50 . I have an upgraded HDR50 and the regular 11 joules and these bad boys are slapping hard ! I'd hate to be on the receiving end of these. I recommend these.
Richard
2025-04-16 21:41:12
These are heavy steel balls but it says they're 59 caliber. They are not. They're just a bit larger. Too large for a 50 caliber paintball marker gun. Great for a slingshot though.
J. T.
2025-03-29 18:34:18
Do not leave it in the open it will rust easy especially the one been recycled/reused. For a pistol that are 4 - 5 joules & around 250-300 FPS, in my test its only effective within 10 - 12 feet in 50-57 degrees Fahrenheit weather ( the warmer the weather the better for Co2 to perform, more power ) . It can soar up to 20 feet but no longer accurate it may go downward and it may have weak impact. But in 10 -12 feet it's devastating, it went through 2 or more water filled Soda cans, you can actually hear the thump when it hits a brick or concrete. I don't wanna be the receiving end of this huge Steel BB. Don't' take my work for it, try it you will like it. I am not sure if it fits the revolvers/HDR, i read some comments regarding that. But it fits my Lancer Tactical Scorpion Pistol. I get around 14 effective powerful shots ( the first 8 shots are powerful ) and the rest i just used the lighter rubber/nylon balls and aluminum balls to shoot paper targets.
Billy
2025-03-26 14:48:39
Good purchase it’s exactly what you expected
Spronez
2025-03-11 09:19:39
Bought these to replace steel balls for the game Bullseye Ball and they are exactly the right size and weight. The tolerances/variance of these replacements are right on par with the original game steel bearings.Measured with a micrometer and weighed in grams to 2 decimal places, the bullseye originals and these are all equally close to the correct ideal size of 0.5" diameter, and 8.5g.These steel balls work with the game and there's no appreciable difference when using them. Visually they are slightly more grey than the originals. My daughter could not see the difference but I was able to notice the originals are ever so slightly more bright in their shine.With a pack of 100 for $20 I don't ever have to worry if i lose any; I will have plenty for the game. Adding extra to the game tray also makes it easier to score points faster. I also have plenty of steel balls should I need ammo for a slingshot in the future.
ron
2025-01-05 12:14:02
Good Ammo
Ti Hua Yen
2025-01-01 18:42:32
The balls are of correct size and weight, but don't have a good polish as in the photo. It is just a semi-glossy finish dark grey metal. Not very satisfied.
Irene Brintalos
2024-12-26 11:52:35
Was used for a chemistry project for school.
Recommended Products