Your cart is empty.
Your cart is empty.
Mechanical Characteristics
- Total Rotational Angle: 300° ± 10°
- Rotational Torque: 10–200 gf.cm
- Rotation Stopper Strength: Minimum 3.0 kgf.cm
- Push-Pull Strength: 5.0 kgf.cm
- Click Position: Center, 11/21/41 Detent positions
- Click Torque: 150–350 gf.cm
- Switch Working Angle: ≤ 50°
- Switch Working Torque: ≤ 350 gf.cm
Electrical Characteristics
- Total Resistance: 10KΩ – 1MΩ
- Total Resistance Tolerance: ±20% (for resistances over 1MΩ: ±30%)
- Power Rating: Curve B: 0.05W; other tapers: 0.025W
- Max. Operating Voltage:
- Curve B: 50V DC
- Other tapers: 25V AC
- Residual Resistance:
- R ≤ 250KΩ: 0.1% max. of total resistance
- 250KΩ
- 10KΩ ≤ R: 10Ω max.
- Insulation Resistance: More than 100MΩ at 250V DC for 1 minute
- Withstand Voltage: 1 minute at 250V AC
- Gang Error: -40 to 0 dB ≤ 3dB
- Rotational Noise: Less than 100mV
Tech Reviewer
2025-08-26 18:00:32
Er... on the listing!Jokes aside, these are great. 9/10 arrived fine, 1/10 arrived bent, but it was just the 'clip' part not the actual electrical pin, so after adjusted it with some needlenose pliers it's impossible to tell a difference from the others.I'm making a midi/DMX controller with these (and some buttons, and LEDs, and other things...) so I only needed 9 (8 for channels and 1 for master). Happy with these - a little 3D printed enclosure and some 3D printed knobs make for a perfect project box!
baxter the basset hound
2025-07-30 12:20:08
These pots feel sturdy and well-built. The included hardware is minimal and could benefit from lock washers, but the overall quality and performance are excellent for the price. There was slight bending of pins from shipping but it was easily fixed.
Todd K. Moyer
2025-05-15 16:34:09
The good:These pots have quite smooth action. The feel is excellent. I tried to set a voltage on the wiper based on 10.0 V input across the 2 outer terminals, and it was reasonably easy to get with 0.1 V of my desired setting.The not-so-good:You only get 1 washer and 1 nut per pot. Generally I've seen a flat washer, a lock washer, and 2 nuts (the 2nd nut can be used as a sort of spacer, behind the panel). All the hardware is thrown in the bag together with the pots, and you're liable to see some bent pins.All in all, not a bad set, at a pretty attractive price. For non-critical applications, these are great.
Torte
2025-02-18 15:12:10
This is a 10 pack of 10 kiloohm potentiometers. They make great level controls, are dirt resistant, and have a low profile and are ready to be surface mounted. They include a washer and nut for each and come loose in an antistatic bag. Highly Recommended!
Ken J.
2025-02-10 16:52:35
All tested under 5% of the rated 100K, and adjustments were smooth and predictable. I was able to easily adjust in increments of 1K. These are sturdily built and have 4 mounting prongs, which should make for durable project use. 5 stars overall, would order again.
Recommended Products
