Shopping Cart

Your cart is empty.

Your cart is empty.

14 Pieces Lathe Boring Bar Set 4 Pcs 95 Degree S07K/ S08K/ S10K/ S12M-SCLCR06 Lathe Boring Internal Turning Bar Holder with 10 CCMT0602 Carbide Inserts and 4 Pieces Wrench

4.9 (8) Write Review
Free shipping on orders over $29.99

$30.99

$ 14 .99 $14.99

In Stock
  • Package includes: you will receive 4 pieces SCLCR06 lathe boring bar turning tools holders, including a S07K-SCLCR06, a S08K-SCLCR06, a S10K-SCLCR06 and a S12M-SCLCR06, 10 pieces CCMT0602, metal indexable turning insert blades, sufficient quantity and easy to replace
  • Quality material: lathe boring bar turning tools holder are made of quality cemented carbide and tungsten steel; The cemented carbide material makes the turning tool durable and adaptable; Indexable carbide turning insert blades are made of cemented carbide and use PVD coating, the blade is sturdy, low friction coefficient, wear-proof and stable
  • Suitable size: the diameter of the S07K/ S08K/ S10K handle is 4.92 inches/ 125 mm, S12M-SCLCR06 is 5.9 inches/ 150 mm; cutting angle is 95 degree, cutting direction is right hand; Applicable machine tool is lathe; Each tool holder has a black oxidized smooth surface, and the tool hardness (HRC up and down 48 degrees) and has nice accuracy
  • Easy to store: insert 10 pieces of cemented carbide into a boxes, and put them in a plastic container, safe and easy to store, compatible with SCLCR06 lathe boring bar turning tools holders; Tight impact bolts, simple structure, often applied for small hole processing
  • Note: due to the slight color change of manual measurement and different display settings, please allow a difference of 1-3 cm; Due to the difference between different monitors, the picture may not reflect the actual color of the item


Product Description

1
2

3

S07K-SCLCR06

1. Overall length:125mm/5inch

2. Boring bar diameter:7mm/0.27inch

3. T8 wrench

4. Threading insert: CCMT21.51/CCMT060204

3

S08K-SCLCR06

1. Overall length:125mm/5inch

2. Boring bar diameter:8mm/0.3inch

3. T8 wrench

4. Threading insert: CCMT21.51/CCMT060204

3

S10K-SCLCR06

1. Overall length:125mm/5inch

2. Boring bar diameter:10mm/0.4inch

3. T8 wrench

4. Threading insert: CCMT21.51/CCMT060204

3

S12M-SCLCR06

1. Overall length:150mm/5.9inch

2. Boring bar diameter:12mm/0.47inch

3. T8 wrench

Threading insert: CCMT21.51/CCMT060204

4
6
6

Notes:

Please allow small errors in size due to manual measurement.

The color might be slightly different due to different displays, please refer to the actual products.


Terry
2025-07-17 16:46:53
Worked out great. The inserts held up for what I was doing. No complaints.
SHB
2025-07-15 14:37:18
Nice inexpensive set of tools. No frills, no major problems it’s all very boring… One issue I noted working with 316 SS (the only material I’ve used these on) while using either of the 2 smallest tools I did get a fair amount of chatter. I chalked it up to operator feed and/or speed error and switched to the largest boring bar as soon as I had the clearance to use it. These new boring bars and the addition of a small misting cooing system purchased on Amazon as well, my lathe has never turned out better parts!
jason ruch
2025-06-09 10:49:53
Great price for the at home hobbyist
DotDotDot
2025-06-06 15:37:22
I needed a smaller diameter boring bar, but one that would reach a couple of inches longer than the one I have. The small one worked very well. You do need to have or make a tool holder. I made one out of half inch key stock - bored in with the drill in the chuck, and this in the tool post. Then drilled two holes in the side and tapped for a set screw. Works very well. The cutting bits themselves will fit all three boring bars, and are VERY sharp. Well worth the money.
Chase
2025-06-01 16:19:56
I ordered this set, and paid more for it, specifically because it had a depth ruler engraved into the side. I don't have DRO, so this would be really helpful. It is a fine set, but the feature is missing. Every picture on the page has those ruler marks on it, but not the actual product. I needed to do some boring, so I'll keep them. Fine product but some false advertisement.
Rusty orgeron
2025-03-22 15:18:22
Great set of boring bars and inserts!!! Definitely recommend worked great on my jet 1024 lathe!! Good price too!!
steven gambone
2025-03-02 18:51:43
I'm a hobbist machinist, it does the job, bang for the buck, can't beat it, bad side it's from Chine,
42 of 3.14
2024-11-17 12:13:38
You know the drill, I try to scrape up something useful to say, some cutting edge remarks. All I can think of is, you screw the insert in place, mount into the holder and dig in.They have not bent or snapped so all is good.