Your cart is empty.
Your cart is empty.Product Description
Compatible With
These sleeves work with most hinges, The length is 80mmand，the inner diameter is about 11mm，Outer diameter approximately 11.9mm.The thickness of the sleeve is 0.45mm.Our products are used closely with Garage door parts. If your rollers and hinges have too much dirt or are not within our size range, they are not suitable.they fit tight on the roller stems and work best with new rollers or rollers with clean stems.
High-Quality
Garage Door Hinge Quiet Roller Sleeves Made from high-quality materials for ultimate durability Manufactured to meet or exceed strict quality requirements.High quality, durable and reliable under extreme conditions.
Package Contents
22x Garage Door Hinge Quiet Roller Sleeves ;22x Roller shaft gaskets.Please check whether it matches your Garage door hinge roller before purchase.
Reduce Noise
These Garage Door Hinge Quiet Roller Sleeves are applicable to the roller shaft of the household garage door. Before installation, the dirt on the roller shaft should be cleaned.If the roller bar rusts or is difficult to install, it is recommended that you treat the surface of the roller bar. Alternatively, apply a thin layer of grease on the inside
- ID-11mm；OD-11.90mm；L-80mm
Antone
2025-06-30 15:22:34
Used with the DURA-LIFT (SKU DLMR6200ZZ) garage door rollers worked great.
Annette
2025-06-11 18:58:21
Works to reduce noise
Thomas P. Taylor
2025-05-14 13:26:32
Impossible to install in my standard garage door. I purchased new nylon rollers and attempted to install the plastic sleeves. I first tried slipping them onto the roller after they were installed but they were too tight. I removed one of the hinges and removed the roller. I then successfully installed the sleeve and tried to reinstall the roller but the hinge socket was too tight to fit the roller with the sleeve installed. I tried to separate the opening a little with a screwdriver to no avail. I promptly boxed up the sleeve kit and returned them. I would NOT recommend these and feel the they are not worth the effort to try and make them work. You could probably accomplish the same thing by installing a piece of shrink tubing on each roller. The shrink tubing is thinner and would accomplish the same effect.
Geno II
2025-05-07 17:46:52
Plastic sleeves fit well, but locking clips are very difficult to install. No instructions were provided for either.
Badger
2025-04-21 14:36:48
Had to remove the hinges to install this properly. The plastic sleeve makes it super tight to fit the roller, but can be done with enough patience. The retainer ring was next to impossible to fit by hand, ended up using a 12mm socket to hammer it in with the roller face on the floor.
MICHAEL GROGAN
2025-03-22 14:01:42
These were easy to install and really quite down my door.
JFE
2025-03-14 10:42:51
Top and bottom roller bearings did not fit at all so noise did not reduce much . Plus the locking washers were difficulty to put on without some creativity. Save your money .
Raz
2025-03-02 18:38:46
If you are replaciong your steel garge door roller wheels for the much quieter nylon wheels, then it makes sense to add these sleeves to the wheels since you are removing the hinges and can easily add the sleeves to hopefully make the door even quieter. I am sure the sleeves reduce the movement and noise of the wheel shafts in the hinge for a quieter affect.
Lester Yuen
2025-01-05 12:58:56
Should have listened to the previous reviews .They are slightly too narrow can only get about an 1/8 of the tube onto the roller .I tried soap and very little water in the tube along with some garage roller spray lube with no success, too bad.
Leyland Williams
2024-11-25 17:24:00
Tight when installed causing roller to not float and accommodate any misalignment in the tracks
Recommended Products