Your cart is empty.
Your cart is empty.Product Description
- Driven pulley bore size - ID : 5/8''
- Driven pulley diameter - OD : 6''
- Driven pulley bore size: 3/4" Bore
- Outside circumference is 27 5/8''
- Width is 3/4"
- Designed for small engines with up to 8hp.
- Replaces Comet 219456A
- Fits GO KARTS, MINI BIKES, DIRT BIKES, ATV'S, LAWNMOWERS, GENERATORS AND MORE.
Replace Part Number: Comet 219552, Manco 5957, Yerf Dog Q43201W
30 Series Driver Clutch, 3/4" Bore, Replaces Comet 219552, 5957
This is a brand new aftermarket asymmetrical 30 series complete driver clutch with 3/4'' ID hole.
Perfect replacement driver clutch for small engines with up to 7 HP
Widely used on Yerf-Dog, Manco, American sportworks, Ken-bar and Murray.
725 belt is included.
It will replace Manco 5959, Comet 30 Series Drive Belt #203589, and Kartco #7628.
Habits That Could Ruin A Clutch
1.Driving too slowly: A clutch starts to engage in the Engagement Speed. Driving at full throttle gives the clutch a chance to cool down. Full throttle locks the shoes in the clutch against the drum. When the clutch is not locked up, it will cause tremendous heat which dries up the lubrication in the oil impregnated bushing and damage the clutch.
2.Short stop and go driving: The longer you drive at full throttle the better off it is for the clutch, because it gives it a chance to cool off before the next engagement.
3.Driving with the foot on the brake: Drive with one foot on the pedal, be it the brake or the gas but not to press on both pedals at the same time.
4.Changing the size of the tires: Putting on tires that are larger than what came with the kart will cause premature wear to the clutch.
5.Restrictions: Don't try and reduce a go kart speed by limiting the travel of the gas pedal or by putting a restrictor in the carburetor to limit full rpm. Either of these methods will result in the clutch slipping, which is self destructive.
Caleb & Bre Merchant
2025-08-16 12:22:32
I thought a knockoff Comet wouldn’t last long, but to my surprise, it has lasted longer. It seems to be higher quality than other knockoffs I’ve tried.
Anna M
2025-06-22 17:51:11
Works just as good as the $60 one I had
Customer
2025-05-06 19:23:02
A perfect fit made for a quick job. The kids are having fun.
Jessica
2025-05-04 17:10:48
Inside diameter of hole is too small. Tried to make it fit but had to reuse some of old parts to make it work. Belt was incorrect as well. Description said one thing and what was sent was another.
Vilhelms
2025-03-22 16:40:13
Fits perfectly and works flawlessly. I wanted to keep the Jack shaft setup and did a little research before ordering because some of the reviewers don't seem to realize there are larger bore, smaller bore, metric, made for TAV, so get your calipers out.
Deanna
2025-03-06 13:46:52
All parts worked good but the belt was the wrong size.
Hey 34
2025-02-03 13:00:56
Works great on yeti dog 3203
V6bird
2024-12-18 18:42:54
This product has worked to stop belt breakage on our Coleman KT196 Go Kart, however the parts weren't milled properly. The keyway was not fully milled which causes the parts to improperly slide together. DO NOT FORCE IT!! If you force the keyway to mate you will bent the rod. I had to file the keyway channel on the torque converter to allow it to slide. You need a thin enough file to be able to get it in the channel without rounding off the corners. There is a similar issue with the back plate on the clutch where the new plate will not fit. I had to reuse the original back plate. Also keep in mind that the new back plate does not have the two roller bearings, it uses a wide brass ring instead. So truthfully I was happier with the original as I feel it will have less issues with friction.I have also noticed that the go kart runs slightly slower now. My son doesn't care because he is just happy to ride again, but it was noticeable to me. All in all, for the price I was happy, but if you are not comfortable or if you didn't know you could file the keyway this set would have not been able to have been used.
Recommended Products