Your cart is empty.
Your cart is empty.Featuring a special release liner, this pressure-sensitive adhesive works with thin, flexible materials where gap filling is not needed. For hand applications only, it bonds graphic nameplates and overlays to metal and high surface energy plastics in the aerospace, medical and industrial equipment, automotive, appliance, and electronic markets. Adhesive Transfer Tape, Acrylic, 2.3 mil
DC Hiler
2025-08-28 16:04:05
Have used this product many times before, and this roll works as good as the others.
Petre I.
2025-08-04 11:23:08
3M 467MP (2.3 mils adhesive thickness) or 468MP (5.2 mils) work very well after the surfaces to be bonded are well cleaned with rubbing alcohol. For increased bonding strength to most surfaces and especially for rubber materials make sure to use 3M Tape Primer 94.
Donald Levine
2025-07-23 14:26:00
I use this on the back of all my solar placards and my customers have never complained about it not sticking. Actually used 1000's of times on exterior installations. I will continue to reorder.
Zora Marie
2025-07-19 10:24:12
Though this is not as good as the older 3M transfer adhesive, it does get the job done and is clear when applied. I will note that it often does not cleanly remove from the wax paper, forcing you to waste both adhesive, time, and sometimes forces you to completely restart projects.Because I am a graphic design student and often have to construct mockups on short notice, this is a fantastic tool and allows me to avoid the downfalls of glue, but remember that it does have its own downfalls.
Kindle Customer
2025-07-12 16:39:32
Make sure you notice this is only 1 inch, not like photo
M. Franks
2025-07-06 13:08:19
The best adhesive that I have found for guitar pick guards. Invisible and thin.
Justin P.
2025-06-18 13:11:58
adhesive sticks to the back of the tape once you start to unwind it, not sure what's wrong with it but this is the worst tape I've ever used.
Bob Adkins
2025-06-02 17:18:41
No matter what I stick this to it sticks harder to the backing. Forget anything even slightly porous or textured, there's no chance it will work. The item must be very smooth and clean like metal, glass, smooth paint, or non-textured plastic and it must be super clean. Even then, I can't get it to stick. Surely this is a defective lot, because it usually sticks to the backing tighter than anything else. Hey 3M, when I pay that much for an item, I expect it to work.
Vincent
2025-05-27 21:28:55
Utilisé pour coller des accessoires dans ma voiture. La colle est très puissante et résiste bien aux chaleurs intenses de derrière le pare-brise. Je cherchais un double face puissant avec une faible épaisseur, ce Scotch fait parfaitement l'affaire.
Alberto
2025-02-18 13:38:24
Es cara y encima no es la que pedÃ.
Marco M.
2025-01-18 15:45:27
Con questo biadesivo, sono riuscito ad attaccare delle cose dove tutti gli altri biadesivi hanno fallito.Bisogna solo fare attenzione ad utilizzarlo, la parte biadesiva non ha una base rigida, è la parte che va tolta che gli da la rigidità . Questo vuol dire che bisogna prima posizionare il biadesivo con la pellicola protettiva, e poi toglierla quando ci si deve attaccarci qualcosa.Non perdona errori di posizionamento, una volta messo, se si prova a toglierlo si comporta come uno strato di colla altamente elastica.Utilizzato principalmente per scaldare il piatto di vetro della stampante 3D, in mopdo da avere una trasmissione del calore migliore.Usato anche per tenere la scritta FIESTA (stampata in 3D) sulla carrozzeria della macchina, ad oggi dopo 4 mesi alle intemperie non si è ancora tolto.
ragazzo07
2025-01-05 16:21:00
Idéal pour protéger un document
Spielkind XXL
2025-01-04 11:00:09
Die Klebefolie ist super.Ich brauchte die um eine PEI Platte auf das Druckbett meines Prusa i3 Steel zu kleben und an meinem Mendel i2 eine Pertinaxplatte auf das MK2 Heatbed.Lässt sich super verarbeiten, kam sicher verpackt und so wie das Tape klebt ... Ist es sicher frisch und hat nicht schon Monate irgendwo herumgelegen.Kann das Klebeband wirklich jedem 3D Druckenden empfehlen.
Recommended Products
