Your cart is empty.
Your cart is empty. Features:
Fits all our temperature controllers
This item has been tested in good working condition
Allows forming and bending of the thermocouple without the risk of cracking
Operating Temperature: -100–1250°C
Probe Material: Stainless Steel
Probe Diameter: 5mm
Threads Size: 8mm
Probe Length: 100mm
Cable Length: 3m
Cable External Shielding:Stainless Steel Braiding
Cable Internal Insulation:Fiberglass
Connector: Spade Type
Package includes:
1Pcs K Type Thermocouple
Art
2025-08-01 14:00:49
I use this thermocouple with a Flute multimeter to confirm that the hot air from SMD Hot Air Rework station has the correct air temperature. Compared the measurement results with the results from another known (and expensive) instrument. The test results are consistent.
Garrett J Roach
2025-07-28 16:37:29
Very accurate, but don't get it wet. I submerged it many times using it to measure the temp of my mash for beer Brewing. Eventually the probe started to read inaccurately. I purchased a new one and all is well again. Lessen learned.
Roark
2025-07-05 16:05:19
This is a decent quality type K thermocouple, but please be warned: the ad says “1250 Câ€. NOT A CHANCE. Make that “C†an “F†and you’re good. I used this as an EGT probe in a mini turbine. At 1600F it melted the probes metal casing which promptly disintegrated and blew itself apart. If you are using it under about 1400F, you should be good, and it will work fine. Just dont believe that 1250C rating. Totally bogus.
Gary Cooper
2025-07-02 09:44:25
Good value works great
KMJ Esquire
2025-06-09 18:20:20
My Cerakote cabinet wouldn’t work - and then I replaced the thermocouple with this unit and it is spot on!
Schnickley P. Wumpledinger
2025-05-15 12:29:48
I bought this to replace an earlier one. This one would not register temperatures over 1306°F (an it is supposed to go up to 1250°C which is 2282°F). This caused my furnace to overheat and did about 1,000 dollars of damage to my equipment. This is the first time I have used this thermocouple and it failed. I am not happy and will not buy from this company ever again.
Michael J.
2025-05-08 16:46:38
Replacement for similar thermocouple that went bad after 2 years of use. If I get the same life out of this one, I’ll be happy.
R B
2025-04-30 10:19:58
My powder coating oven PID was showing a temperature that didn't match my BBQ sensor that I used for checking.After some verifications, I found that it's off by 10%, which means at 400 degrees, it's off by 40 degrees which is completely unacceptable. That was the old sensor.I purchased this sensor and now I'm confident using my oven's PID controller because the temperature is within 2 degrees even at 400 which is more than acceptable for powder coating.Very glad I went with this unit.
Jorge A.
2025-04-27 16:13:09
La seriedad
Art
2025-04-04 12:50:12
I use this thermocouple with a Flute multimeter to confirm that the hot air from SMD Hot Air Rework station has the correct air temperature. Compared the measurement results with the results from another known (and expensive) instrument. The test results are consistent.
Garrett J Roach
2025-03-16 09:37:39
Very accurate, but don't get it wet. I submerged it many times using it to measure the temp of my mash for beer Brewing. Eventually the probe started to read inaccurately. I purchased a new one and all is well again. Lessen learned.
Roark
2025-03-12 17:07:45
This is a decent quality type K thermocouple, but please be warned: the ad says “1250 Câ€. NOT A CHANCE. Make that “C†an “F†and you’re good. I used this as an EGT probe in a mini turbine. At 1600F it melted the probes metal casing which promptly disintegrated and blew itself apart. If you are using it under about 1400F, you should be good, and it will work fine. Just dont believe that 1250C rating. Totally bogus.
Gary Cooper
2025-03-10 16:08:55
Good value works great
KMJ Esquire
2025-02-19 10:23:17
My Cerakote cabinet wouldn’t work - and then I replaced the thermocouple with this unit and it is spot on!
Schnickley P. Wumpledinger
2025-01-21 10:12:11
I bought this to replace an earlier one. This one would not register temperatures over 1306°F (an it is supposed to go up to 1250°C which is 2282°F). This caused my furnace to overheat and did about 1,000 dollars of damage to my equipment. This is the first time I have used this thermocouple and it failed. I am not happy and will not buy from this company ever again.
Michael J.
2025-01-10 15:22:31
Replacement for similar thermocouple that went bad after 2 years of use. If I get the same life out of this one, I’ll be happy.
R B
2024-12-04 15:47:50
My powder coating oven PID was showing a temperature that didn't match my BBQ sensor that I used for checking.After some verifications, I found that it's off by 10%, which means at 400 degrees, it's off by 40 degrees which is completely unacceptable. That was the old sensor.I purchased this sensor and now I'm confident using my oven's PID controller because the temperature is within 2 degrees even at 400 which is more than acceptable for powder coating.Very glad I went with this unit.
Jorge A.
2024-12-03 15:14:54
La seriedad
Recommended Products
