Your cart is empty.
Your cart is empty.Product Description
MOCW 4692269AI Battery Current Sensor Fit for Jeep Chrysler Dodge Fiat
- Our sensor dismeter bolt is 8mm, which is thicker than the original one,so the original nut needs to be replaced with a 13mm hexagon nut to tighten. When installing, please ensure that the sensor is directly replaced when the car is powered on (if the battery is dead,require a car jump starter), no additional matching is required after replacement, and the sensor can work normally.
- If it is replaced in the power-off state, the sensor needs to be re-matched through the computer after the replacement is completed, otherwise the sensor connot work normally.
- For Dodge, Chrysler, Jeep, Fiat series can be installed directly；For Honda models, require additional 13mm nuts and keep power-on state during installation. Please refer to the description section for more details!
Replace OE # 38920-TR0-A02, 4692269AI, 4692269AG, 4692269AH, 04692269AG, 04692269AD, 04692269AE, 04692269AF.
Disconnect the negative cable. and loosen the bolt with a bolt wrench. (Always disconnect the negative cable first)
Lift the black lid and then remove the bolt inside with a bolt wrench.
Remove the old battery sensor, replace it with a new one.
Reconnect the cables and bolts. Finish!
A. Posey
2025-08-09 14:57:02
This product fixed my start/stop issues on my 2015 Jeep Cherokee! Like others have said, my car has been plagued for years with “start stop unavailable due to battery charging†messages. I’ve replaced the battery twice, and each time it would fix the issue for 6-12 months before it would slowly lose reliability. I figured it was the battery again, but this time I got a message saying that the start stop system needed service, and with a little internet searching I found this product. I’m honestly not 100% sure what this thing does (measure current?). About 5 minutes to install, 2 bolts and one small electrical connection. After reconnecting, I had a couple of spurious messages about park sense and lane sense unavailable, and that start stop system wasn’t ready, but after driving for about 15min, everything is now working like new!
Evan B Silverberg
2025-06-05 15:41:13
They should call this sensor the "StartStop" sensor because it immediately fixes the errors and issues with it not working, at least for a 2016 KL Trailhawk 3.2 I couldnt find my battery sticker until i removed this sensor. My battery stickers says 11/22 so i dnt think my battery is bad in this case. for 30 bucks this made my start stop work immediately without anything else. Hopefully it lasts awhile and it will save some gas at long lights so i dnt understand people who hate it just press the button then!
Michael Wiggins
2025-05-27 18:10:47
Works perfect on 2018 dodge journey gt. The day I paid my vehicle off it throws a code. Looked it up and narrowed it down to this sensor, found it here at a quarter of the cost compared to the dealer or even a parts store. Threw it on and the code cleared. Would definitely purchase again when the part goes bad.
Korey Murphy
2025-05-26 11:55:59
Missing bolt and nut and isn’t the exact same size as original so you can’t use original nut and bolt
A Knecht
2025-04-27 16:51:29
I was able to install this in about 5 min. Very simple. Haven’t had any issues with it and my car now works how it did when it was new! Great price compared to dealerships!
Customer
2025-03-06 13:59:07
2015 Jeep Cherokee was intermittently showing Stop/Start System error. Jeep replaced this years ago under warranty when the same problem occurred. For less than $35 I thought I would give it a try. It only took a few minutes to install and the problem is resolved.
Wild Wanderer
2025-02-21 14:17:14
I was having issues with the Start/Stop system on my 2015 Jeep Cherokee Trailhawk V6 and this instantly fixed it. I was getting the message "Start/Stop System Unavailable. Service Start/Stop System." This was after being on "Start/Stop System Not Ready. Battery Charging" for a few minutes. Start/Stop now functions perfectly again.When replacing this part, I recommend minimizing how long you have the negative cable disconnected. I've heard that if it's disconnected too long, the system will have to go through a lengthy relearning procedure that will hamper performance awhile. I was able to swap the new one in for the old one in about five minutes.
Jake
2025-02-17 14:33:36
It seems to have fixed the issue I was having. However what should have been a 2 minute job with just a 10mm wrench turned into a 45 minute ordeal that required several tools. The oem part uses 10mm nuts on the clamp and the stud. The new part needed a 13mm(not provided) nut for the stud. But it's not as simple as getting a bigger nut and calling it a day. The negative battery cable is made to fit snugly on the oem stud. So now you have to get a drill and correct bit to open the lug to fit over the new stud. But the cable is in such a spot you can't just hold on to it while you open up the hole, now you need a pair of pliers to hold the cable while you drill. You could skip the pliers of you want to remove the battery, but that just adds more time and another trip to the tool box. But again it seems to be working so it gets a middle of the road rating. There's probably better ones out there for the same price so I'd shop around before settling on this one again
MAD
2024-12-31 15:16:29
Rapport qualité prix c est ok. Pour un Ram 1500 2017.
G. Morissette
2024-12-06 21:33:13
I had the Battery Charging issue on my Jeep Cherokee 2016 for nearly two years now. I've changed the battery and the issue persisted. Immediatly fixed the issue when I switch the ISB Sensor. Thank you very much
Hazem
2024-11-26 13:07:00
very bad product, had to get an OEM replacment, should be covered by warranty not just amazon return window
Wabet
2024-11-14 15:10:19
Didn’t fit a 2012 Honda civic
Recommended Products