Your cart is empty.
Your cart is empty.Product Description
Specification:
1. Input voltage: DC 5V to 12V
2. Circuit board size: 55*37*1.6mm
3. Maximum power: 120W
Package Included:
1*ZVS heating power module
1*Heating coil
When inductive heating, usually work for 5 minutes to power off cooling. Because the current is relatively large during induction heating, the coil heat is also relatively large. When heating, part of the heat generated by the heated object is transmitted to the heating coil. For a long time, the temperature of the heating coil is high. If the heating coil is connected to the terminal, the plastic part of the terminal will be melted. Therefore, when induction heating, it is best to solder the heating coil directly to the PCB.
You can check whether the blue LED indicator light up to see if the power is supplied or the module can functionally work. When the indicator is dim, maybe the power supply is insufficient, should use a higher power supply. Just make sure the power supply is within DC 5-12V.
Operation: heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most don't more than two-thirds.The diameter of the heated object should be controlled within 20mm as far as possible.
Confirm that all components are welded correctly, and the positive and negative power cords are not reversed. After connecting the load (heating coil, high-voltage package), turn on the power again! No power on without load! No-load power on is easy to damage!
Puff the magic goof-ball
2025-09-03 10:59:18
This induction heater power supply works great. Mine has been used daily for weeks and is doing a good job. Tips: do not run the induction heater without a ferrous metal object in the coil, or else it could burn out.Also, it's important to do a test of new units to make sure the work before beginning on your project. Getting a bad one is rare, but can happen.I've had three other induction heater power supply modules that have been working for years. This brand has been very good, so far.
Campbell john walker walls
2025-07-23 16:29:11
Perfect for dynavap, you'll need to find your sweet spot cause it clicks fast no matter what unless you modify it to induce a smaller area. Will make a small bolt or nail red hot possibly liquid (I haven't pushed it that far) you absolutely need to solder these connections to the sides of the board. It functions in the ports but with a load it will start to melt the plastic casing for the output ports.
Patricia
2025-05-09 18:56:10
Worked for a few minutes then stopped working altogether
Paul E. Fox
2025-05-02 20:05:56
Bought mostly out of curiosity. Works very well for SMALL metal objects and will come in handy for my model building.
Erik Swanson
2025-04-21 19:43:30
Buyers of this should be aware that soldering the coil to the board is very strongly recommended by the insert documentation, and to do that you’ll need an actual soldering iron with some decent wattage due to the mass of what needs to be heated to make a good joint. (The 4xAA battery-powered iron I had was not up to the task.)Also, one of the capacitor connections on my unit was broken and I had to resolder it myself. Not a big deal, just annoying.
Phillip Johnson
2025-04-09 15:34:18
Just seems to overheat at the transistors and not do much else..
Rahn Kramer
2025-03-05 11:30:53
The media could not be loaded.
Seby
2025-02-18 17:26:41
Instructions made the assembly very easy. It helps if you have a soldering iron. I also recommend adding a momentary push button and installing everything inside a small project box - just make sure That the coils do not touch the box wall (make larger holes; You could also insert some porcelain rings to ensure the coil wire would not touch the plastic wall).Works great with my small projects in the shed, I’m sure you can use it for jewelry work and other similar type projects. This was a fun and useful purchase.
Josehf Murchison
2024-11-22 16:19:45
It was smaller than I thought it would be however it works well.
Thorr
2024-11-19 16:24:49
12v too much for this. a 1/4 inch nail blew it. 6v it will work well. 3 for lying.
Recommended Products