Adjustable Magnetic Gauge Tool, Camber Castor Strut Wheel Alignment Tool for Car/Truck Camber/Castor Strut

This tool is pretty well-made, and can give you a quick and fairly accurate indication of where your camber setting is.Not a substitute for a real alignment rack check... but it gives your a quick look at the likely setting!

Yes. It's more than the average person needs; but, if you often seem to be hauling heavy stuff around in your car, expect rear wheel camber to go out of wack. It can cost you 100s of dollars in excess wear/tear on your tires--to leave it that way, even to the point of making your vehicle UNSAFE when the camber goes out (protenates either inward or outward causes excessive edge of tire wear/prematurely destroys your tires 10s of 1000s of miles too soon.) Many quick oil / tire shops won't even do the work to align real wheel camber, but if you work on your own car, get this for your toolbox and do it yourself.Tool was easy to use. Process is simple. Tool Price: reasonable. Already paid for itself on my 3 cars 10 times over. 5 Stars. Buy it.

It seems made well and the bubbles are easy to see and appear on the calibration lines without difficulty. The main problem I had using this was it has to attach to a flat surface and if you use the wheel it probably won't be flat. If you take the wheel off, then you need to support the lower a-arm and put the weight of the vehicle back down on it to get an accurate reading. To adjust the control arm you have to also take off the opposite side and do the same to get a reading to set the other side by. A bit complicated and timely but it does work fairly well.

This tool is not used to do an alignment. This tool is used to set camber back to the same place it was after you remove or replace a strut. Some struts are adjustable and have an oblong hole in them. This is used to make a camber adjustment by moving the strut in or out slightly and tightening the bolts back up. Camber is how much the top of the tire tilts in or out and is measured in degrees. When camber is changed it also changes toe. Toe is how much the tires point in or out as viewed from above. If toe is out just a little bit it can wear the inside or outside edge of your tires relatively quickly. I use this tool when I replace struts. If you don't, it is a pain in the ass to adjust camber with the tire on and the alignment machine installed on the rim. The two large strut alignment bolts are next to impossible to reach and adjust to the proper position because the tire is in the way..For best results use these directions:.1. With the vehicle safely supported remove the wheel.2. Slightly snug at least two lug nuts on the brake rotor so it does not tilt. (You may have to buy 2 if they have a chrome cap on them preventing them from being tightened down on the rotor.)3. Install the tool on a flat portion of the brake rotor and level the small level first.4. Turn the knob on the bottom to zero the large level.5. Remove the tool in a way not to touch the tilting level or adjustment screw. Put it in a safe place where it won't get knocked out of alignment.6. Mark a wheel stud and the brake rotor in a way you can install in them "both" in the same position. Remember the position of the marked wheel stud (ex. the 12o'clock position)7. Perform steering or suspension work.8. Rotate the hub so the wheel stud is in the same position as when the tool was leveled.9. Install the brake rotor over the "marked" wheel hub in the same exact position it came off This assumes the hub and brake rotor are the 2 piece kind (like most), not the 1 piece design10. Install the tool in the "same" location and snug at least two lug nuts so the brake rotor doesn't tilt.11. Move the tool in a way to level the small level (Do not touch the adjustment screw)12. Move the strut in or out and tighten the adjustment bolts when the large level bubble is at zero again.13. Recheck after tightening adjustment bolts that it is still at exactly zero.14. Remove the tool and install the wheel.15. Tighten the lug nuts to manufactures specified torque.16. Make sure all parts removed were properly reinstalled.17. Pump up the brake pedal if you had to compress the brake caliper piston to remove it..This tool is better than the "Tool Aid" brand one I previously had. It has a second level (side to side) which allows you to place it back on more accurately. This also has an adjustment screw rather than physically having to move the body to level it. I used epoxy to hold my magnet in. Save the cardboard box with Styrofoam it comes in to protect it.

I'll start off by saying I bought this camber tool despite some of the concerns I read in the reviews. I figured I would give it a fair shake anyways.After actually using it, I decided to return it.It's not versatile or lifesaving enough for me to justify keeping it, and it's definitely not the only option. I'll be getting a digital angle gauge next.I needed to adjust my rear camber and this popped up in the "for you" suggestions.Again, I tried to give a fair shake. So, here we are.This is me reading reviews, pre purchase.1. "The thing leaks fluid if it's left outside during a cold winter or hot summer." That figures. It sucks, but it figures. You get what you pay for. This tool just likes Air Conditioning, I said.2. "Highly inaccurate." It's a level. If you start zeroed out to begin with, you'll get accurate results at the end. Operator error, I said.3. "Mine arrived missing the magnet in the bottom." There's literally nothing I can say to this. *looks at manufacturer for answers*4. "It doesn't work well in direct sunlight. The fluid expands and the bubble disappears"*Looks at manufacturer again*So after reading all that, i bought it anyways. And it worked, albeit with frustrations.I stuck a magnetic 6' level on my garage door beam. The beams exactly 90 degrees so I knew I had an accurate start when I dialed in the tool.When I stuck the tool to the level and got it zeroed out, I noticed the adjustment knob was extremely free and there's no way to lock your settings. I'm glad I left the level stuck to the beam for an accurate 90 degrees, because I used it quite a few times.If you bump that adjustment screw AT ALL while adjusting your camber arms, you're starting over.Go zero your tool out. AGAIN.As far as using the tool, it's super easy.Stick it on the flat surface of a brake rotor or drum after you zeroed out to 90 degrees, adjust your camber arms to your settings, and that's it. You're done.Unless you bumped the adjustment screw accidentally.The adjustment knob REALLY needs a lock of some sort.

For the DIY kind of person use this to get the alignment done on the from of your vehicle, by adjusting the A arm and with a little understanding of how it works you'll make out fine. I did and brought it to the shop to see if I was close and they said they never touched it all was good. =-)

Very useful tool easy to use and great value for money

This tool is awesome to have. If you don't know what your doing or dont know how to use it properly look it up on YT how to set it up. I used this when I did upper control arms on my vehicle and they are known to have camber issues this tool got it correct on the first try. It just works would recommend.

This is not accurate enough to use without going for an alignment after, as a get close tool its ok , but cannot be relied upon to set camber accurately

The phillips screw that holds the magnet on was loose giving false readings,not sure why it comes loose but i cranked it real tight,other than that seems work good to set the camber after installing monroe struts assemblies.