Your cart is empty.
Your cart is empty.Product Description
YzusGomumu AN6 Dual Feed Carb Fuel Line Aluminum Braided Fuel Line Kit For Holley 4150 Carburetor
Replacement:Over time, the stock fuel lines in a car can degrade, especially in older vehicles. Upgrading to an aluminum braided fuel line kit can provide increased durability and resistance to heat and corrosion. It can be a worthwhile replacement option to ensure reliable fuel delivery and prevent leaks or other fuel system issues.
AN6 Dual Feed Carb Fuel Line Aluminum Braided Fuel Line Kit For Holley 4150 Carburetor
Flexible customization: The aluminum braided fuel pipeline kit has flexibility in wiring and installation, making it suitable for customized automotive manufacturing or repair. You can arrange fuel lines according to specific engine layout or installation requirements to better control fuel system settings.
High quality: This is a high-quality fuel line made of aluminum with a braided stainless steel outer covering. The aluminum construction provides durability and resistance to corrosion, while the braided stainless steel provides added strength and protection. The fuel line is designed to handle high-pressure fuel delivery.
AN6 Dual Feed Carb Fuel Line------your best choise!!!
Higher Quality Materials
Enhanced Performance
Easy Installation
K10
2025-07-19 15:46:25
Â
James s.
2025-07-16 15:17:32
its a pain to get it all tightened down but after you do it works fine,
Nevin F. McDaniel
2025-07-01 13:25:38
presure gauge doesn't work
Doug Fender
2025-05-03 15:05:30
As many before me have said, it's junk. I was prepared to have to shorten it, and I did, about 1/2". The outside sheath was woven cotton which frayed, even while using tape before cutting. They may look like AN fittings, but they're not. It comes with o-ring gaskets, but they desingrated from having to tighten so much. Used yellow pipe tape every connection. Sill leaked. Can't go wrong with high quality American made.
Henry T.
2025-02-28 10:02:29
It doesn’t fit correctly.It leaks everywhere. I tried to fix it by putting 0 rings. But it still leaked. So I ended up buying a third one. Haven’t put it on yet. Let’s see what happens.
Heavychev
2025-02-17 11:29:14
Everything sealed first time and have put about 250 miles on it
Michael Hansen
2025-01-16 12:33:06
There is a allen srew on the back side of the t, it does not tighten, and it leaks like a sieve.
Aliviana York 2.0
2024-12-20 09:39:36
I got this to go on a EFI throttle body system. As I was unboxing it, (it ships partially disassembled, only the center hose part is preassembled) I was noticing these black O-rings and thinking to myself, "what the - are these for?"AN fittings don't require O-rings, in fact no tapered seat fittings require o-rings. so I start inspecting it further and there are o-rings pre-installed in the female fittings and I can clearly see junk in the L and T fittings.The L and T fittings are both steel, the L fitting has rust in it, and the T fitting has machining flakes hanging inside it.The female AN fittings fit very sloppy on the L and T, and I am 99.44% sure the steel fittings are JIC and are not AN.The JIC and AN fittings are not compatable and should NOT be used together, this is probably why they stuck O-rings on all the joints....it would leak like crazy.This kit is not high quality, it's just thrown together and not something I would use on a race car. If I had just assembled it and installed it all the bits of Trash and Contamination would have ended up in the carburetor/throttle body because this is installed AFTER the fuel filter !I Hope My Review and Pictures Were HELPFUL to You !!
Recommended Products
$38.66
$ 20 .99 $20.99
$53.99
$ 23 .99 $23.99