Your cart is empty.
Your cart is empty.Product Description
Anyyion Hot Melt Glue Gun Kit is an easy use adhesive tool not only in DIY crafts making but also in daily quick repairs.
The glue sticks come with the Anyyion Hot Melt Glue Gun Kit is environmental-friendly, it has super strong adhesive when glue between 2 different parts, but easy to clean when forced apart these 2 stickup parts, it will always keep your items clean.
About hot melt glue gun:
Material: Plastic & cuprum
Working power: 150~300W
Working voltage: 100 to 230V
Working temperature: 356 to 392℉
Nozzle diameter: 0.070-0.078 inch
Warm-up time: 2~5 minuters
Cable length:55 inch
Size:10.4 inch*8.5 inch*1.5 inch
Color: yellow
Diameter of the glue strips should be 11mm.
Warm Prompt:
1. Keep clean of the glue sticks to avoid impurity block the nozzle, and do not pull out of the remanent glue sticks after each time using.
2. To avoid get an electric shock during using, do not use in humid environment and keep it away from children.
3. The remaining pressure inside the glue gun will push a little molten glue out of the gun even stop use, so to save your glue, please control release the trigger or cut off the power in advance.
4. Cut off the power when stop using, and never try to disassemble the melt glue gun in any case.
Packing List:
1* Hot Melt Glue Gun
Hoist
2025-07-17 16:46:55
Ok, so it’s just another hot melt glue gun, right? Nothing to get too excited about, right? That may be the case for those who are jaded by always having used a professional hot glue gun. For me thought, nothing could be more to the contrary! For the last 25 years I’ve been on occasion using my old 40 watt glue gun, and I can tell you that the difference between that gun and this 300 watt gun is night and day. Apparently the old gun never really got hot enough to really liquify the glue. The glue was molten, but not really liquid. Due to this heavy viscosity it was much much harder to squeeze the trigger to force the glue out if the nozzle. On the other hand however, with this gun it is effortless to pull the trigger and pump out liquid glue. The results are better too with the glue melting much better and cooling to form a much smoother puddle.In the attached photograph you can see my first use if the gun. I have replaced the o-ring that clipped on to the bottom of my bicycle light that affixed it to the handlebars, with a large rubber ring fabricated with the glue gun. Yes, I could have bought a 3-D printer to create a mounting system for the light, but for now I just saved $500 and a few days of work using the hot melt glue gun. Yes I may eventually spend the $500+ and the time to fabricate an ABS mount for the light, but for now I couldn’t be happier with my new hot melt glue bicycle light mount.I’ve also included a picture of the gun in my hand so that you can get an idea of the size of the gun. My size? 6’2â€.Also I thought that I’d mention that that this drips less than my old 40 watt gun. I believe that is because I had to apply much more pressure to get the glue to come out of the nozzle. What the one negative reviewer said about the gun dripping just seems nuts.And me too! To quote the words of another reviewer, I can’t believe I waited so long to purchase this gun!I paid for this gun myself and have no connection to the manufacturer or the seller.Yes I would definitely recommend this gun!
K D Z
2025-06-27 17:01:09
I'm an artist and I use this for work. I like that it has 2 heat settings and lights to show they're working. you also won't find another 150-watt glue gun in this price range. this is my 2nd Anyyion 300W Industrial Glue Gun - I use it that much. I couldn't recommend it more, it's the best!
Pch Enterprises Inc
2025-05-08 16:17:05
For the money, this is a great gun, however it keeps turning itself off if you lay it down on the left side due to where the power switch is located. We ended up just taping it down in the "high" setting and leaving it on all the time if it is plugged in. But regardless, the design is good and it puts out a lot of hot glue. I'd buy it again if this one were lost.Not that it matters too much, but the 60 second heat time is not accurate for us. 3-4 minutes is more accurate, but maybe with very low temp glue it would work more quickly. You still are not going to get more than 3-4 or so feed of a useable bead without giving it a bit to heat up. but it is about 50% better than our 200W gun, which is what you would expect at 300w. I wish some one would create a 600w gun with a thermastat, so lots of glue could be put through, but it would hold at the set temp when setting it down for a bit. I'd pay alot for that!
Arlon Arriola
2025-04-20 13:03:48
I'd say it's exactly what I needed, and it works great. There are some times when it seems to switch off or something - but it's rare, and it comes back. I've glued a ton of stuff with it now, if it does that to me I just switch the switch to the other setting and it starts working again. The 300w mode sometimes puts the glue out too hot, like literally boiling, but between the two modes, switching back and forth here and there, I give this a very high four stars. I don't think you can get a better glue gun for that price, I like it a lot, even with the tiny apparent flaws it has. I didn't measure the wattage, I have no idea if it's really 300 watts or 150 in 150-mode, all I know is I've had other glue guns and this is the fastest one I've used. And it doesn't hurt my fingers after using for a long time, whereas some glue guns I've used (the white $30 one on here) do. I think the tip is exchangeable with the white one I mentioned, that comes with longer nozzles, so between the two, we're going to glue town over here. The nozzle is a bit short so I'm probably going to try out the nozzle from the other one to see if it fits, and I'll update this review when I do. They look pretty interchangeable. Overall, I really like this glue gun, and would buy it again!
glikar
2025-04-03 11:43:39
Did a simple test with the longest nozzle on, bought the nozzle extension package. https://www.amazon.com/gp/product/B074DR2CDB/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1Temperature of the glue coming out the long nozzle end was 368F at the guns highest setting and pumping glue out at a steady rate, so I think that is pretty good considering 1.2 inches of exposed copper tubing.Only minor negative so far is the sides of the gun around the heat element warmed up enough to release the glue on the labels. No big deal, the handle stays nice a cool. Looks like they designed in a long body in the handle area to keep it away from the heat. So the disadvantage is to the manufacturer since they lost their branding on the gun.Setting the heat works very well and I like the temperature display. It's used mainly for hobby builds so it's handy to have a built in temperature reference when using foam and other material with a low melting point. I have no hesitation giving this one five stars!
babak ali abolhassani
2025-03-10 20:18:32
This glue gun stopped working after the first use! The tip barely heats up and no glue comes out. Dont waste your time or money on this. I made the mistake of not testing this glue gun for a few months after I purchased it in November. Last week I had a chance to use it. It worked well the first day. I turned it off then plugged it back in the next day and it failed to work, very little heat at the tip and no glue will come out.
Pierre Rivest
2025-03-02 15:19:53
La lumière d'indication de sélection de température a mal fonctionné le lendemain de l'utilisation. Je l'ai retourné et obtenus un remboursement sans aucun problème
michael
2025-01-16 12:52:23
can not keep up to glue i need to apply waiting for an answer from seller
Recommended Products