Your cart is empty.
Your cart is empty.Product Description
If your car's front bumper has only 2 non-standard pre-drilled holes
If your car has not holes but needs to install a front license plate
Well, Our front license plate mount kit is the right choice for you!
Easily complete the front license plate mount without damaging your existing bumper.
Advantages of our Front License Plate Holder Kit:
1. There are multiple mounting holes on the black plastic license plate bracket, which can be freely adapted to the pre-drilled holes of the bumper in different positions;
2. The screw hole with copper metal thread firmly locks the license plate;
3. Nylon license plate inserts (expansion nuts) insert nuts to replace your old license plate inserts;
4. High-quality stainless steel ties to secure the plastic bracket and bumper to prevent loosening;
5. 2 self-tapping screws or mechanical bolts. to install the bracket to the front bumper;
6. 4 M6*12mm anti-theft mechanical bolts fix the tag plate on the license plate holder;
7. Black license plate screws caps covers and washer;
BurtB
2025-08-19 15:50:07
Needed to relocate the license plate on our Class C motor home after adding a spare tire carrier to the trailer hitch receiver.Since this particular carrier really blocked the license plate where the original plate is located.I spotted this kit that included a new light, and ordered it.While the instructions are fairly limited, if you have experience with drilling in fiberglass it is pretty easy to install this.I first used blue painters tape to cover the area where the holes would be drilled. Then I positioned the holder/frame and uses a small level to make sure the plate would be level. Then I marked the two holes to drill for mounting.I started with a fairly small drill and kept increasing until I had a hole that was just large enough to work the two nylon screw clips into place.Finally I temporarily mounted the holder and light and located where to drill a hole for the wire for the light. I used the smallest drill that would allow the wire to fit.Note of course that you need to verify that there is nothing behind where you need to drill like wires or hoses, etc.And, of course, if you are just using this as a fancy frame for your existing location then it is easier to install.I put the four supplied self adhesive pads on the corner of the plate and the frame on the back side. In addition I added some additional self adhesive tape to provide more protection for the fiberglass where I installed the holder/plate.In my case I had easy access to the rear of the fiberglass, it might be more difficult in other installations.One other review I had read before purchasing complained about cheap plastic and breaking when installing. The frame is metal as advertises. The LED light is plastic and as such you need to use some caution when tightening the mounting screws.I didn't have any issues due to tightening the mounting crews.At present the LED light is working great, time will tell how it holds up.Once I was ready to mount I fed the wire through the small hole
Orion
2025-08-10 10:34:14
The front license plate on our old van had taken a beating over the years, with minor dings and scrapes. The holder was cracked, but the bumper was fine. The plate was a little torqued, but was still usable.Getting the OEM plate holder off was not difficult, and I was relieved to find the bumper underneath damage free. This substitute plate holder fit one of the holes well, while the other side had a vertical slot that was usable. I attached the holder to the existing holes and made sure the screw in the vertical slot was extra tight. Getting the plate on the holder was a piece of cake. I used the security screws that came with the holder, which made things easy.The holder has held up fine, and was an easy and cost-effective solution.
Meta
2025-08-07 17:31:27
Super easy to put on and fits good! Good purchase for the money and nice and sturdy.
Z
2025-08-04 17:31:51
Slots did not align with where the mount divots were located on 2010 Subaru Forester (subtracted one star). However, was able to extend two existing slots on this frame with a drill and now works well for my purpose.
Charles Schenfeld
2025-07-31 13:49:26
For the 2014 CR-V, there is nowhere to mount this. The number of rating stars is irrelevant. It looks to be a quality product, just not useable for my purpose. Drilling anywhere on the front facia risks damaging sensors.
Customer
2025-07-23 13:30:45
Went on easy and works well
Yung Kim
2025-05-20 18:11:18
This is an okay product, but I had to make some adjustments to make it work. First the holes on the Audi front mounting area did not line up with any of the openings on the bracket. I had to drill through the bracket to center it. Then when I went to put the license plate frame on with the provided screws and plastic concealer dots, the left side would not catch the threads unless the plastic washer cap was removed. The right side had no issues but for whatever dressing the left side was just coming up short. So I ended up mounting the plate without the hideaway black dots. It ultimately works but the screws need to be a little bit longer and the mounting bracket needed to be altered to work for me.
Melissa O.
2025-03-24 10:03:28
Fits great on my Expedition, not wanting to drill straight into the bumper this holder keeps the plate in the correct spot and looks nice doing it.
Customer
2025-01-30 09:57:06
remorque de motomarine
Client d'
2025-01-29 16:24:04
Satisfait
Recommended Products