Your cart is empty.
Your cart is empty.Never compromised on quality, fully equipped with state-of-the-art technology - Designed with the user optimal experience in mind. International Renown, constantly modernizing powerful devices to meet the demands of the modern user.
the gman in NM
2025-08-06 12:32:35
Firstly, shipping was super fast which is always good. Secondly, item appears to be well made and finished. No sharp edges anywhere, it's difficult to describe but if you're a tool person, you know what I mean when I say it feels good in the hand.Cuts metal within the limits of the specification easily. As with most air tools, it is very loud in operation so ear protection is recommended. Air consumption was fairly accurate I think. You're not going to be happy using it with a small pancake air compressor as it will cycle all the time. I have a 60 gallon 5hp compressor and it cycled enough while using the nibbler that I could tell a smaller compressor likely wouldn't work very well.I used it for cutting holes in 29g metal roofing panels and it sometimes struggled when it came to cutting through the ribs, just because of the acute angle caused as the throat of the nibbler went from the flat of the sheet to climb the rib. A little practice and it became a bit easier to force it to climb.One thing I didn't see covered in the manual is that you can actually change the orientation of the cutting head. As shipped, it cuts directly in line with the long length of the tool. However, by loosening the main nut on the head, you can switch the cutting direction by 90 degrees at a time. Hence, if you needed to trim something at a right angle to the handle, you can simply switch the head in less than 2 minutes. This was a nice feature.I didn't lube it every time I used it but enough that I could tell the difference when it needed air tool oil and it runs very well with good lube. Overall, I am very pleased with this tool and would unreservedly recommend it.
Diesel Ted
2025-07-30 16:18:16
Cutting trailer roof panels 100% worth the money. Cuts like butter
David H.
2025-07-03 10:48:33
was perfect for the job no issues
Don
2025-07-01 21:42:49
This is a very high quality tool. It cuts very well on 18 gauge CR steel that I use for old car patch panels. The only problem I have is that there's no mark on the cutter to allow you to follow a line. To cut a straight line, it works best if you can clamp a straight edge (wood or steel) to make a fence. If you try it free-hand, you will likely end up with a wavy cut line. It cuts very fast and, yes, it does produce a lot of small crescent shaped waste pieces, but I don't find that a problem. When I cut wood with my circular saw, I have a lot more of a mess to clean up than the small metal pieces this cutter makes. I deducted one star for the lack of a guide mark on the cutter.
J-Son’s Auto and Racing
2025-05-31 15:33:33
I have used one of these in the past but forgot how great they are to use. I have a plasma cutter, cut off grinders both pneumatic and electric and this little guy is faster at cutting over all of them.It is a smooth cut and very fast. It does eat out about an 1/8 of an inch of the material, but if you want to cut a lot of (flat) metal quickly, this thing gets it done.I don’t know how long it stays sharp, I have made a lot of cuts with it, and it’s still working good so far. I prefer it over all the other tools I have.
Demon Camber
2025-04-25 15:05:12
Two week experience with the tool:From my initial use on 26gauge steel it can cut it easily. However it seem to bind or get stuck and require force to push it through the bind. Tried 90-150psi it didn't have an effect on performance...In videos I've watched about this tool this doesn't seem to be an expected behavior.Cons:- Binding during straight cuts (not sure if this is something that nibbler do from time to time)-1/4 npt air inlet out of spec in other words it was too large... 1.To large for a 1/4 npt milton fitting but not large enough for a 3/8 npt. 2. I could bottom out the fitting and have an air leak with tape 3.Used industrial paste for large gaps to seal itFuture plans :I order a second one from a different vendor for comparison. The Ingersoll Rand looks vastly different then most models on here. It will be interesting to see if it performs better.Side thought:The general design of the tool resembles some of the poorly rated Chinese models out there. This is just an aesthetic observation. (Since I don't have one those on hand and cannot compare the internals)
Kyle R.
2025-04-03 10:18:43
This nibbler will cut 2024T3 0.063", don't know how long it will last doing it but as for now it cuts it. I Tried to cut 7075T6 0.063" it will kinda cut that but the tool is not happy about it. Both of these materials are thicker than what the tool is rated for in steel. They don't list capabilities in Aluminum Alloys so it's kinda trial and error to see what works for this thicker stuff, I'm sure it would cut any AL Alloy just fine If it is 0.050" or thinner
Preston spires
2025-03-16 15:05:23
Works great
StyleDeVie
2025-02-14 17:09:09
Ne semble pas être bien adapté pour une coupe en ligne droite pour de la tôle ondulée de toiture et pour le soffit, il a du mal à passer les bosses de la tôle.Sinon l'outil est de bonne qualité et facile à manoeuvrer, la coupe est nette, franche et propre. A été utiliser avec un compresseur à air (de 110 psi environ).
Ridley
2025-01-24 12:36:51
Totally disappointed when I got it, I can see that there are sign or people trying to open this item using a spanner with the amount of scratches on it. I return it immediately
Mathieu Moore
2024-12-14 15:44:22
Perfect ! Thank You !
Johanne Dumoulin
2024-12-09 17:07:53
Reçu en bon état et fonctionne très bien
ChrisD
2024-11-19 12:09:05
Good for the job I needed
Recommended Products
