Your cart is empty.
Your cart is empty.Product Description
Made of aluminium and brass, rust and corrosion-resistant. Pneumatic operation is easier and faster than manual operation.
Coolant delivery hose
Cooling system vacuum refill kit with delivery hose can change coolant in 10-15 minutes quickly.
Vacuum Purge Operation
- Drain residual coolant from the system as much as possible.
- The three ends of the T-type connector connect the air compressor or vacuum pump (top), the discharge hose (bottom), and the vacuum coolant refill tool (left).
- Select a suitable rubber adapter to attach to the radiator and turn the gold rotary knob clockwise to seal it.
- Open the on/off valve on the brass tube, start vacuuming when the pressure reaches -25 to -20 inches Hg (-50 to -60 cm Hg). Then close the valve and air source.
Coolant filling operation
- Select a suitable rubber adapter to attach to the radiator and turn the gold rotary knob clockwise to seal it.
- Connect the T-type connector to a 59-inch coolant delivery hose, the end of the hose is fully immersed in fresh coolant.
- Open the valve and coolant enters the radiator.
SET INCLUDES
Make sure the adapter sizes fit your vehicle; the coolant vacuum refill kit should be operated under professional guidance; high temperature coolant may be sprayed under pressure, be careful when opening radiator cap; no air compressor or vacuum pump provided.
Trusty Dusty
2025-08-13 11:02:40
If you're like me, you've probably done radiator flushes the same way your grandpa showed you yesrs and years ago. After all, it's free, you just dump it in the radiator and burp the system. This system makes it so you do not need to burp it at all - but it goes further than that. More and more cars for packaging reasons have made the top of the cooling system be somewhere other than the radiator. Because of this, it can be very difficult to work out the air bubbles, sometimes taking several heat/cool cycles. Worse, if you think you got all the air out, and you're driving down the road and start overheating, now you could be looking at a head getting warped.More than anything else though, this saves time. The setup takes a few minutes, and then another few minutes for the vacuum to draw in the coolant. The whole fill process took less time than doing a single fill/burp cycle.Also - it is cool to see the system draw so much vacuum that the coolant hoses quite literally shrivel up (It's supposed to). In a way, that itself is a good thing because if you had a marginal hose, you would rather it break now, then down the road.
no
2025-07-22 15:05:17
Could it be better built, yes. Does it do what you want it to, yes. I don't own a car shop but I do maintain 5 vehicles. One recently required me to get this tool and even mechanics struggle to buy it for 150-200. This one is decent enough, value built and has all the accessories I needed
Honest buyer
2025-05-07 10:25:03
Returned for a different more expensive model with not 3 but 4 size rings Plus a rubber cone adapter.Because on my 90 Buick Century, the overflow tank is flimsy and couldn’t handle the vacuum there. So I had to vacuum at the radiator cap neck but even without the size rings, it was still too big to fit in the inner mouth of the opening.Otherwise one it seemed to work alright.You’ll want to super glue the 2 nice little rubber red grips on the wing valve. Because they fall off easily otherwise.It seems this is not designed to suck liquids(directions are for an empty system-just flushed etc).So if your system is already full of coolant, you’ll want to use like a Turkey baster to temporarily suck out a small volume equal to what would come up/out when the radiator hoses collapse under the vacuum.Otherwise it’ll spit the liquid coolant and have trouble bringing the vacuum down as low as prescribed.Then you can add the coolant back when vacuum is done, by shutting the valve and removing the compressor fitting and adding the add coolant hose fitting so it’ll get sucked right in when ready.
Customer
2025-05-05 20:41:07
Works well for a cars with closed cooling system, ford, dodge.
Matthew
2025-04-21 15:59:56
Everything about this product was cheaply made and I couldn’t get it to hold vacuum. It has basic mechanical parts a Venturi just redirects are to create vacuum. All it has to do is be airtight and it couldn’t do that. I would advise you buy a different one
Dustin Kelley
2025-03-16 09:15:29
This works just as good as the ones that cost 150 or more great buy for anyone needing one
brad
2025-01-22 17:18:28
2017 Ford Taurus (and Explorer). Worked perfectly. No quality issues, no leaks.
Demetrius Butler
2025-01-10 14:32:34
When I put the part on the reservoir it didn't seem to hold the pressure.
Recommended Products
$68.50
$ 27 .99 $27.99