Your cart is empty.
Your cart is empty.Product Description
Why are DRL daytime running lights necessary ？
- This daytime running lights led strip can make your vehicle more visible in bad weather such as rain, fog and snow.
- This DRL led strip can help you drive safely and avoid traffic accidents.
- MAKE YOUR HEADLIGHTS POP!
●Start Up: White dynamic sweeping when start-up.
●Driving: As a driving light, it will be constant white light when the car is running.
●Turn Signal: When used as a turn signal, the yellow strip light flows in sequence.
Feature
Waterproof
This led turn signal strip has a waterproof design, it can be used normally in rain, snow and car wash.
Bend at will
The DRL LED strip can be bent, twisted, and contoured to fit most headlights.
3M Adhesive
The back of the sequential led strip with high-quality 3M adhesive, can be directly attached to the outside of the car fixed, easy to install.
Specification
Voltage:12V
Wattage: approx 3W per strips
Size: 430mm x 14mm x 4mm
Light Color: White&Yellow
Quantity: 2Pcs
LED Modules Quantity: 14
Package Composition: 2PCS DRL daytime running lights strip(R+L)
Kyle koontz
2025-08-16 14:22:19
Great product i.bought other i sidnt like these one work.perfit
dwayne
2025-08-02 13:12:03
Very good
Zoomzoom87
2025-06-24 14:34:02
Fairly bright for $20 lights. I installed these on the inside of my headlight housings. But the biggest thing I bought them for was for the sweeping action they do on start up like it shows in the video. These do not do it at all. They just come full on and that's it. Very disappointed, spent a couple hours to install them where I want them and they don't work like they are supposed to. Sequential blinker does not line up with the blink sequence of the stock blinker like my other products I've bought. They have their own timing and just make it look weird like your blinkers are out of sync. Would not buy again.
Frank
2025-05-31 17:19:28
Ami carro le quedaron perfectas
Kelly Guerrero
2025-05-05 14:29:38
The media could not be loaded.
Brian Curtis
2025-03-08 21:58:51
These are interesting add-on DRL/signal lights. They're made with a flexible PCB, using individual clear plastic reflectors over each LED segment. Each segment consists of 6 LEDs, 3 white and 3 amber. The entire assembly is contained within a clear heat shrink tubing, both ends filled with silicone for limiting liquid ingress. Everything else (connectors and drivers) are not water resistant at all.They work as described in the product information, with the signal markers flowing in one direction when activated. The DRL LEDs turn off during signal operation, then come back on a few seconds after signal operation stops.My concerns with this product are as follows:1. The reflectors have alignment pins that protrude through the flexible LED pcb. These pins are small and therefore a bit poky. I can see them wearing through the clear heat shrink tubing after a while due to vibrations (you can easily feel the pins through the heat shrink right out of the box).2. While the PCB is flexible in the forward and backward direction, it's not all too flexible up and down. When flexed either up or down, the PCB starts to kink.3. Attachment is via double-sided foam tape. This would be fine if you didn't have the alignment pins sticking out the back, as well as an unmarked 8 pin SMD chip on the PCB backside. This reduces the foam tape coverage on the backside of the light strip to about 30%. Replacing the included foam tape with a high-quality and thicker foam tape would be recommended.4. While the lights themselves are fairly well protected from water, nothing else is. You'll need to find a way to protect the JST connectors and control boxes from water ingress. The control box PCB is not conformal coated.Some mounting considerations are required. We'll give them a go and see how it turns out.
Fue genial... gracias
2025-01-05 10:42:19
Llega muy rápido. Espero funcione bien. Se ve excelente
Recommended Products