By far the best mic arm I have ever used. Flawless in movement and holds from as well.

UPDATE - 4/11/2024My original review (see below) only gave this stand 3 stars. I had an issue with the design of the ball joint that attached the mic to the stand. I left the exact same review on the BEACN site. The customer support team reached out to me after reading my review and seemed quite surprised at my concerns. They told me that what I experienced was not normal and should not have happened.After just a bit of back & forth, they offered to send out a replacement in exchange for my sending the defective unit back for them to look at.Long story short, they sent me a replacement stand and after setting it up, I experienced none of the same issues. I am now questioning whether my initial issue might have been due to user error when I set it up. I am waiting to hear back from BEACN to see if I can establish whether the mistake may have been mine or if I simply got a defective one. When I hear back, I will update this review.Regardless, once this issue was addressed, this stand became the absolutely perfect stand for my setup. The low profile and swivel design allows me to position the mic when I'm using it without the stand getting in the way of other equipment. It also allows me to swing it completely out of the way when I'm not using it. Setting up for a recording or meeting is now literally as easy a pressing a button to set my lighting and swinging the mic right into position.The build quality is excellent, the motion is smooth and quiet.Finally, sometimes things happen. Whether the ultimate cause was user error or a defective unit, once BEACN was properly aware of the issue, they made it right without any hassle!------------------------------------------------------------------------------------------------------------------------I love the overall design on this stand. It's sleek, minimalistic and sturdy overall.So, why only 3 stars? In the end, there's one significant flaw, and it finally reached the point where I simply couldn't use it anymore. The ball joint interface between the mic and the stand. The single screw that locks the ball join in place and interfaces with the stand simply doesn't work well for me. When the screw is tightened, it locks the ball joint well. However, the simple clamshell design that actually attaches to the mic stand itself simply can't hold the mic steady in the vertical. That connection, no matter how tightly I screw things down, can still rotate 180 degrees on the mic stand connection. I position the stand so that I can swing it out of the way when I'm not in a meeting or recording. The process of swinging it back into place often causes the mic to drop down. That even happens if I happen to gently bump the mic or try to reposition the stand more than a fraction of an inch.It's really unfortunate. I like EVERYTHING else about this stand it would be 100% perfect and get 5 stars from me in an instant if this one issue was addressed. However, it's just not usable, and believe me, I tried for nearly four months!

Coming from someone who’s used literally dozens of different mic arms I have go say this one goes all the way up to where it’s comparable to the Rode PSA1+. I used the elgato low profile mic arm before this one and I was satisfied enough, but it started to get more and more issues. I use a Shure SM7b microphone and it’s notoriously heavy for a mic, so over time the elgato mic arm started to slouch a ton and it looked really ugly, and started to have really bad wear and tear the longer I used it. This mic arm has no such issues and moves back and forth so clean it’s actually insane. If you are looking for a mic arm, this is the one to go with, even if you’re not looking for low profile this will do everything you need, guaranteed.

Very good quality for the money. Like the way you can hide mic cable in arm

Most excellent arm. Works flawlessly - can highly recommend. Found out you can use just the first section - the one with the mic attachment - if you want to which was my case, that first section will plug right in to the base support. Also great customer support very fast reply!

I’ve recently purchased this BEACN mic stand, and I couldn't be happier. The installation process was a breeze. Adjusting the stand arm to my preferred height and angle is simple and easy, allowing me to find the perfect position for my podcast recordings. One of the standout features I needed was the ability to swivel the mic arm out of the way when I'm not recording. This flexibility helps keep my workspace organized and clutter-free. I specifically wanted to avoid a traditional mic stand that would take up desk space (as you can see my desk is small). The quality is there; the arm feels very sturdy and is made from high-quality metal. Plus, it matches the black color scheme of my desk.Overall, I recommend the BEACN mic stand and mic for anyone looking for a functional, aesthetic, and space-saving solutions!

I first saw this used by a video content creator on YT.Though it is designed for a desk (in the sitting position), I have it clamped onto a music gear flight case...which is set atop a keyboard stand...and is perfect for my use while recording vocals (standing).

Pretty underwhelmed for the price. It's fine, but I would like more vertical movement options. I am pretty easy to please, but for whatever reason this product didnt hit the mark for me.

I was worried that it wouldn't be worth the price since it's more than other arms but I have absolutely 0 regrets! It feels very sturdy and the motion is smooth and soundless.Surprisingly, my favorite feature is the cable management. There are no covers to pull off and struggle putting back on. The rubbery "bristles" (pictured) are easy to push the cable through and make adjusting the length such a breeze.It's a premium product that's 100% worth the premium price

The initial box was missing parts and had chipped paint. This was sold from amazon which means it was a open box return being sold as new. As I mentioned, the arm itself is awesome but amazon less so.