Your cart is empty.
Your cart is empty.Product Description
If your windshield glass is damaged or if the sealant is leaking, you may need to remove and replace your windscreen. Removing windscreens takes patience, skill, and high-quality car windscreen removal tools you can rely on.
This kit comes with all of the tools you need to get to the windshield and effectively remove it. You’ll get the urethane cutting wire you need to get through most windshield urethane.
You also get:
- 275 mm panel-removal tool with handle,
- 330 mm Starter tool,
- 330 mm, 2x handles for cutting wire,
- 180 cm cutting wire,
- 240 mm Trim pad remover,
- pull scraper with handle and pull rope
Operation Guide
- Remove all panels which are inside within the range of the adhesive material with the removal tool.
- Unwind some cutting wire and push it through the adhesive material by using the piercing awl. In case of narrow space, heat up one tip of the cutting wire with a lighter and gently push the hot wire through the adhesive material. Therefore you need to hold the wire with a pliers.
- Shorten the cutting wire to desired length.
- Attach the tips of the wire to the handles by pushing the wire through the lower opening of the hollow shaft until it can be inserted into the bore hole at the upper part of the shaft. Snap the wire and push back the shaft into its handle.
- By going back and forth, the wire heats up and starts working through any adhesive material.
- ATTENTION when working in narrow space. The cutting wire can damage painted surfaces and covering panels.
- Residual fillers or adhesives can be removed by using either the double hook handle or the pull scraper.
worked great,
July 25, 2025
Used it on two windows already worked amazing. Only issue we had is the wire broke a lot. But that could me because we have never done it before hard to tell.
Bill W.
July 20, 2025
Good quality and value
It fit and it helped I recommend this product
July 15, 2025
For just to use it to remove 4 Glas it's good but not too sturdy
Patrick Collins
June 7, 2025
Not good product wire snaps very easily tools dull and fragile best to purchase parts individually for better quality
Hallstar
May 19, 2025
Great product. Works great
Thomas R. Harris
May 13, 2025
A relatives Toyota Tundra had the back glass get busted during a bad storm. It might have been the adhesive Toyota uses or the blade is made of an inferior metal, but the glass removal blade was bending and getting distorted while using it. It did eventually get the job semi done, but not sure it could handle a second job.
Miranda
April 26, 2025
The kit is fantastic to have on hand and beats the snap on and Marco prices!
Ramiro Carrillo
April 22, 2025
This kit worked perfectly on removing a windshield from a 1999 Toyota 4 runner that I was parting out. I heated up the insertion tool prior to feeding the wire thru the urethane on the windshield. Did not use a sawing motion at all, simply pulled the wire with the handles at sharp angles and the wire sliced thru the sealant with ease. 20 mins and I had the windshield out. For the price, I recommend it
worked great,
April 21, 2025
Used it on two windows already worked amazing. Only issue we had is the wire broke a lot. But that could me because we have never done it before hard to tell.
Bill W.
April 11, 2025
Good quality and value
It fit and it helped I recommend this product
April 7, 2025
For just to use it to remove 4 Glas it's good but not too sturdy
Patrick Collins
March 23, 2025
Not good product wire snaps very easily tools dull and fragile best to purchase parts individually for better quality
Hallstar
March 17, 2025
Great product. Works great
Thomas R. Harris
March 14, 2025
A relatives Toyota Tundra had the back glass get busted during a bad storm. It might have been the adhesive Toyota uses or the blade is made of an inferior metal, but the glass removal blade was bending and getting distorted while using it. It did eventually get the job semi done, but not sure it could handle a second job.
Miranda
February 21, 2025
The kit is fantastic to have on hand and beats the snap on and Marco prices!
Ramiro Carrillo
February 2, 2025
This kit worked perfectly on removing a windshield from a 1999 Toyota 4 runner that I was parting out. I heated up the insertion tool prior to feeding the wire thru the urethane on the windshield. Did not use a sawing motion at all, simply pulled the wire with the handles at sharp angles and the wire sliced thru the sealant with ease. 20 mins and I had the windshield out. For the price, I recommend it
Recommended Products