Enjoy free shipping on orders over $29.99

US Dollar

0 $0.00

Your cart is empty.

Centrifugal Clutch Go Kart Clutch 1' Bore 14 Tooth for #40/41/420 Chain Compatible with Go Kart Mini Bike(1' Bore 14T)

4.6 (8) Write Review

Free shipping on orders over $29.99

$22.99

$ 9 .99 $9.99

In Stock

Qty.:

【Compatible with】Go kart centrifugal clutch 1" bore 14 tooth for #40/41/420 chain- up to 13hp horsepower，engagement speed: 2000±100 RPM.Compatible with go karts and mini bikes
【Package included】 1 x 1'' Bore 14T go kart centrifugal clutch, 2 x screws(Chain Not included)
【High Quality Material】A high quality and professional clutch made of high quality iron material that is high impact, wear resistant maximum torque and durable
【High Quality Material】Lightweight, sturdy & durable, high impact, wear-resisting, fast heat dissipation, stronger and features maximum torsion
【Before Purchasing】Please check carefully up and below information about our go cart clutch 1 "bore 14T shaft fitment before your purchasing, any question, please contact us first, thank you!

Product Description

How to install a new clutch on a kart?

Step 1: First, we need to remove the outer drive cover. Loosen the drive chain by loosening the nut at the bottom of the engine mounting plate so that the engine has enough room to slide backward. This step requires careful operation to prevent interference during subsequent installation.
Step 2: Remove the drive chain from the drive wheel sprocket (shaft sprocket). This process requires the use of appropriate tools and ensuring that the sprocket is not damaged during operation. When removing the bolts and washers at the end of the engine crankshaft, be sure to pay attention to the correct position of the new clutch gaskets and washers to prevent errors during subsequent installation.
Step 3: Remove clutch from engine crankshaft. Make sure that the clutch key holes are perfectly aligned with the keyway on the crankshaft before installing the new clutch onto the crankshaft. After installation, slide the clutch onto the shaft to check whether it is stable.
Step 4: Reinstall the clutch bolts and washers on the crankshaft to ensure that all components are properly installed without any interference or loosening.
Step 5: Reinstalling the drive chain on the clutch and drive wheel sprocket (shaft sprocket) is a crucial step that requires careful handling to ensure its stability.
Step 6: When the engine has slipped back to the proper position, we need to tighten the chain. When the chain has been deflected to about a quarter of an inch and the appropriate tension has been obtained, the next step can be taken.
Finally, the seventh step is to tighten the nuts at the bottom of the engine mounting plate and reinstall the outer drive cover. After this step is complete, make sure that all parts are properly secured without any loose or abnormal noise.
During this process, care must be taken to install guards to protect occupants from rotating parts. Do not overlook any details, or it may have a serious impact on the performance and safety of the vehicle. Be sure to follow all safety regulations and operating guidelines.
For some potential risks and precautions, such as unexpected situations or failures during operation, we need to take appropriate measures. During the installation process, it is important to maintain a calm and orderly operation to avoid accidents. It is also important to ensure that all tools and equipment are properly prepared and in good working order to be able to respond quickly in the event of an emergency.
In general, implementing a new clutch installation requires careful handling and precise steps. By following these steps and paying attention to safety matters, you will be able to successfully install a new clutch on your kart. I hope these instructions have been helpful and good luck with your installation!

Fitment：

Fit for #40/41/420 chain- up to 13hp horsepower，engagement speed: 2000±100 RPM.Compatible with go karts and mini bikes

Chain NOT Included:

Mounts onto crankshaft using bolt and washer on the end of the crankshaft. (Clutch does not need set screws as long as the end of the crankshaft is threaded to accept a bolt. Most go kart clutches are held onto the shaft with a bolt and larger washer. Extra washers if needed are used on the crankshaft to space clutch.)

Clutch Bore 1"：

1 x 1'' Bore 14T go kart centrifugal clutch, 2 x screws.

The Centrifugal Clutch 1" Needs Be Oiled Before Use:

Don't put oil inside the clutch holes: The holes on the drum are to let the hot air out of the clutch. When oil gets in the drum portion of the clutch it will cause excessive slippage, which means undue heat will be generated

david angier

2025-09-03 12:56:12

This product was everything I needed to be able to enjoy my mini bike! I would recommend this company and this item!!! Clutch is still going like it's brand new!!!Thanks guys!!

Susie

2025-08-22 14:17:27

Glad that they work great for what they are needed for.

Alan G.

2025-08-15 20:48:58

This clutch fits a 212 cc 3/4 bore engine. So far it's been a pretty good clutch

Mike O.

2025-07-21 18:09:43

I was looking for a heavy duty clutch and I found it. This one weighs a little bit more than the others Iâ€™ve purchased but they didnâ€™t hold up. Iâ€™m a dad riding mini bikes with his boys. Love how smooth it is to.

joshua

2025-06-03 12:30:07

Do not waste your money! Fits as specified however it will not engage! Just slips and gets red hot! Right put of the box and doesn't work. I wouldn't but another one!

Customer

2025-04-18 18:15:28

Works great just needs a cover

Crystal

2025-01-22 12:18:58

Fit on our Coleman kt196 go-kart

Brenden Asmussen

2025-01-12 18:06:02

The stall was too low, wonâ€™t allow the engine to idle without being under load.

Shopping Cart