Your cart is empty.
Your cart is empty. Applications
The anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment
The anchor is designed for use in a Wet environment.
Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor
The diameter of the anchor is 3/8".
Length Anchor
The length of the anchor is 3-3/4"
Thread Length
The length of the threads on the anchor is 2-1/4" in length.
Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.
Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-7/8". This will ensure that the minimum embedment of 1-1/2" will be met.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".
Torque Value
To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft./lbs.
Spacing between Anchors
Each anchor must be spaced a minimum distance of 3-3/4" from each other when measured center to center.
Edge Distance
It is very important not to install the anchor any closer than 1-7/8" from an unsupported edge of the concrete.
Yellowdog
2025-07-17 17:13:58
Used these anchors on our new outdoor steel pergola to tie into the concrete patio. Easy to use and a solid anchor. Only wish there was a dozen in the pack as I had to buy 2 pack to finish the job. But now I have 8 more to do other projects.
Sammy
2025-06-08 13:47:12
Way cheaper then the big box stores and worked perfect
scott w.
2025-05-28 12:24:02
Good Quality, Reasonable Price
Hank V
2025-05-06 14:06:36
For those of you who are familiar with the construction of a screened swimming pool cage, where the bottom channel is 2" wide and 1" high, which is OK where your pool cage is build on a concrete slab, the way ours used to be, until we had 1-1/4" pavers installed on our pool deck. (Which looked and still do look great)When we had the pool cage replaced a few years ago, the 1"X 2" bottom channel is now at least 1/4" below the surface of the pool deck, which for all intend and purpose makes is a catch all for all the crap that gets blown around when I pressure wash the pool deck.OOPS I almost neglected to mention that I changed the 1"x2" bottom channel to a 2"X2" extruded splined channel,(hence the need for the 3/8" x 5" SS WEDGE ANCHORS) along with the 3/8" SS cap nuts which not only looks GREAT, but also will make it a LOT easier for my GOOD WIFE to keep it clean. Sorry for the Helter Skelter ramble, it is getting pretty late for me to be writing this reportRegards. Hank V
Blake Parquette
2025-03-24 18:46:49
Made in China, but very good quality. Bite down very well. Installation specs are available on their website.
Tide Pride
2025-03-22 15:48:53
performed as needed
koyote ken
2025-02-27 15:15:44
I needed SS anchors for securing a pool handrail in to the cement deck. These really fit the bill.They have a different grippers on the bottom part. They grab more effectively and really "stick" in the hole.Highly recommend.
Dmac
2025-01-31 09:54:42
Quality stainless steel. Used the 3/8†x 3 3/4†to secure a gazebo. All washers and nuts were there, nothing missing.
GANG CAO
2025-01-12 21:16:24
There are ten washers in total but five are missing.
Recommended Products
$30.99
$ 13 .99 $13.99