Your cart is empty.
Your cart is empty.Product Description
9pc Blind Hole Inner Bearing Puller Set Remover Slide Hammer Internal Kit 8-32mm
· 8 - 10MM (51/6" - 13/32")
· 10 - 12MM (13/32" - 15/32")
· 12 - 14MM (15/32" - 9/19")
· 15 - 17MM (9/32" - 11/16")
· 17 - 20MM (11/16" - 25/32")
· 20 -24MM (25/32" - 15/16")
· 25 -29MM (1" - 1-1/8")
· 30 -32MM (1-3/16" - 1-1/4")
HAMMER WG. 100MM / L -2. 15LB (940G)
3 POUND SLIDE HAMMER WITH T – HANDLE
DROP FORGED HEAT TREATED STEEL ATTACHMENTS
HEAT TREATED PRECISION MACHINED STEEL BOLTS
REMOVES GEARS, PULLEYS, & STEERING WHEELS
SEPARATES BALL BEARINGS
SLIDE HAMMER SHAFT: 1.2FT LONG (390mm)
tracy
2025-09-01 19:21:15
Worked great
Ninjanick650
2025-08-22 09:27:36
The media could not be loaded.
Dylan H
2025-08-13 12:18:41
This tool is roughly built and the opposite of refined.. Had some blind bearings that needed to be replaced on a mountain bike, shouldn't be too tough, definitely easier than working on an vehicle. Made sure to heat the aluminum bike frame up a bit to make it as easy as possible, tightened the tool down and made sure everything was secure. And nothing. Couldn't even get the bearing to budge and the threads of the tool immediately started stripping. Absolutely failed to even remove a single bearing. And the bearings weren't seized, without too much difficulty I was able to use a punch and carefully knock them out in the end. Should have listened to some of the other reviews on here. I've had lots of luck with "cheaper" tools, usually if you're careful and go slowly they work out. But this one was just a failure.
James G
2025-08-09 11:31:06
This kit is pretty good. It does the job.PROS: great price, a pretty good selection of sizes, case includedCONS: case is not as durable ask I'd like - pieces don't lock in super securely
Shy
2025-07-18 15:52:40
Budget friendly and will get the job done. Great product
L Roy
2025-07-06 17:42:15
I ordered this hammer works great just want I ordered
Bobby
2025-04-28 19:22:00
I didn’t have high hopes for this at the price point, but it pulled 5 bearings that had been in my spoke wheels for 17 years. They never slipped or deformed. I highly recommend!
Brian
2025-04-10 21:32:42
Perfect
Dallin frost
2025-03-28 09:49:25
It’s great for small engines like dirt bikes and quads. yes sometimes it slips out of the inner bearing, by I remove it so only the outer remains wich makes it far easier.I was skeptical of the reviews at fist but it’s a quality slide and fittings. Great buy for $50 that I should’ve bought months ago for my other engines.
Karim
2025-02-28 12:54:18
alors j'ai voulu l utiliser de la bonne façon mais ca n'a pas fonctionner l outil glisse et fini par sortir de sa prise donc je me suis dis si comme ca ca ne fonctionne pas je vais faire dans l autre sens donc j'ai remis l outil et au lieu de tirer vers moi avec la masse a inertie j'ai pris une barre en fer et j'ai taper sur l outil dans l autre sens et même comme ca j'ai eu du mal a sortir le roulement qui pour mon cas était vraiment soudé a la jante d un coté les roulement ont 150K km et ils ont bien rouillé sur les bord je précise c était une jante avant de MT 07 si vous avez réussi avec ma technique n'hésiter pas a mettre "utile" comme ca je vois si j'ai aider beaucoup de personne aller bon courage =)
Christer
2025-02-12 15:26:50
Har inte testat den ännu men verkar stabil i konstruktionen och passar många storlekar.
Wouter V.
2025-01-14 10:36:17
The collet that the manufacturer says is for 15-17 mm starts out at 16.0mm, so you have to compress it with two pliers (which is extremely unergonomic) to get out a 15 mm bearing.The collet one size smaller only goes to 14.6mm when you screw in the pin fully.Didn't try any other collars. Build quality is decent.
Aland de Hepcee
2024-12-24 10:30:53
Acheté pour extraire 2 roulements de 22mm bien rouillés. Ils sont sortis en 3 ou 4 coups de marteau coulissant. L'outil n'a pas été abîmé. Toutefois, ça reste du chinois pour usage occasionnel
Recommended Products