Your cart is empty.
Your cart is empty.Delphi's mechanical fuel pumps, which work with older-model carbureted systems, deliver fuel flow to the engine. It sits at the front-lower portion of the motor and the pumps are lever-operated. An internal diaphragm draws fuel from the tank through lines running the length of the vehicle and pushes the fuel into the carburetor.
Matthew
2025-08-27 11:04:08
This went on a daily driver so it had to be reliable. It’s been installed for years and still functions like new. Doesn’t loose prime unless it sits for several days. Starts right up every morning and never had a vapor lock issue. Excellent value for the money.
Rdwarr
2025-08-26 20:39:00
This pump fit perfect and works great
Pam
2025-08-13 16:35:46
These are junk...do not buy...they leak fuel...
Customer
2025-07-27 11:23:32
Perfect fit
Randy Bentley
2025-07-23 18:16:52
Ok. I put this pump on my sbc 350 this morning. and it works great. to great for some reason it's putting out 2 1/2 times the psi almost 15 psi. that is way to much for my carburetor which 6.5 is max I can run it. It will blow out my needle and seats. Luckily I only paid $16 bucks. Is it worth it to send it back. I don't know.
MWBWMW
2025-07-21 10:03:28
Bought two of them. Both were pumping double the pressure they should be which caused my carburetor to flood out. I ended up putting a used one on and now it runs just fine.
Edward
2025-07-02 10:09:02
The MF0001 Inlet size is for 3/8" ID fuel hose. Outlet size is for 3/8" flared tubing (5/8" line wrench), same as the inlets on Holley or Quadrojet 4 barrel carburetors and not for the 5/16" flare tubing Inlets on Rochester 2 barrel carburetor. The MF0020 pump is the 5/16 x 5/16 Inlet/Outlet pump.
Derrick
2025-06-23 18:59:01
Fits perfect comes with everything except push rod but looks good
Ahmed zaki
2025-06-19 10:17:41
It did not last me even 500 kilometers. It leaked fuel from all directions
Barry
2025-06-12 18:47:28
No issues , works well.Only ran motor for 2 minutes but looks / works good in that test run.
Eldon W.
2025-06-07 15:59:38
It works great
Dwayne Remraf
2025-06-06 11:53:07
Happy with the product
Matthew
2025-05-22 15:16:52
This went on a daily driver so it had to be reliable. It’s been installed for years and still functions like new. Doesn’t loose prime unless it sits for several days. Starts right up every morning and never had a vapor lock issue. Excellent value for the money.
Rdwarr
2025-04-30 11:24:41
This pump fit perfect and works great
Pam
2025-04-29 18:28:59
These are junk...do not buy...they leak fuel...
Customer
2025-04-13 11:27:28
Perfect fit
Randy Bentley
2025-04-11 10:07:31
Ok. I put this pump on my sbc 350 this morning. and it works great. to great for some reason it's putting out 2 1/2 times the psi almost 15 psi. that is way to much for my carburetor which 6.5 is max I can run it. It will blow out my needle and seats. Luckily I only paid $16 bucks. Is it worth it to send it back. I don't know.
MWBWMW
2025-04-06 16:13:04
Bought two of them. Both were pumping double the pressure they should be which caused my carburetor to flood out. I ended up putting a used one on and now it runs just fine.
Edward
2025-04-04 16:58:11
The MF0001 Inlet size is for 3/8" ID fuel hose. Outlet size is for 3/8" flared tubing (5/8" line wrench), same as the inlets on Holley or Quadrojet 4 barrel carburetors and not for the 5/16" flare tubing Inlets on Rochester 2 barrel carburetor. The MF0020 pump is the 5/16 x 5/16 Inlet/Outlet pump.
Derrick
2025-03-31 12:22:16
Fits perfect comes with everything except push rod but looks good
Ahmed zaki
2024-12-29 11:53:32
It did not last me even 500 kilometers. It leaked fuel from all directions
Barry
2024-12-17 14:39:59
No issues , works well.Only ran motor for 2 minutes but looks / works good in that test run.
Eldon W.
2024-12-14 12:22:01
It works great
Dwayne Remraf
2024-12-11 11:48:25
Happy with the product
Recommended Products
