Your cart is empty.
Your cart is empty.The DEWALT 20V MAX* DCF622 Screwgun with Versa-Clutch features a DEWALT built brushless motor capable of up to 2,000 RPMs. DEWALT impact wrench delivers the torque needed for heavier duty fastening applications.
Fierce Ginga
2025-09-05 10:28:02
After firing my contractor who was doing the barn steel on my building I knew I needed something easier to use than an impact or drill. This is the answer. I imagine I put close to 10,000 screws in with the screw gun. It performed beautifully. When installing screws with washers you have to pay close attention. You can't over sink them yet can't not tighten them. I used the features of this screw gun to get precise with that and it works great.everyone doing exterior barn steel should have
jack johnson
2025-07-31 17:57:39
You make it I'll buy it great quality I'm very pleased
Tyrone
2025-07-30 15:35:43
Excelente muy buen producto
Good job!
2025-07-23 12:47:44
Everything was good!
Joshua Collier
2025-07-17 11:09:42
I’ve been installing metal roofing for years and I just wanted to add that this screw gun I purchased from Amazon really changed progress for the better thanks Amazon
Hammer
2025-07-14 13:47:49
I bought this as a cordless powerhead for a Simpson Quik Drive Pro300S system. This motor adapted well. The power allows me to run heavier screws than drywall. I use it for cement board (CB3), subfloor (WSV) and the pressure treated deck (DSV). It is a lower cost option than the Fein that Simpson offers. Battery is a 5 ah, which I had, and will last about 3-6 hours depending on tge screw. Great motor for what I need it to do!
Lazaro P.
2025-07-12 19:56:37
Excelente
John Brown
2025-06-28 16:07:01
This tool must have been designed by engineers who have never used a power tool. It's ergonomic, lightweight, powerful, and a total piece of garbage: if a bit breaks off or gets stuck, it is impossible to remove it from the nosepiece: you have to buy a whole new nosepiece, (the black part forward of the trigger.Here's the scenario: I am up on a roof, happily driving screws. I drop a hex bit while swapping it out, and it rolls off the roof. I reach into my pocket and find nothing but a short (1/2") phillips bit (not the inch long ones you'd normally use). 'Well, I'll stick it in the dewalt and finish the job before climbing off the roof.'I just ruined my freaking screwdriver.The half inch bits are literally impossible to remove from the DCF622's nosepiece. They push in far enough that just a bit of the point sticks out, and YOU CANNOT REMOVE THEM, even with tiny powerful needle nose pliers.I stuck the driver in my vice and spent hours pinching and poking. I tried cutting off the end of the bit and drlling into it with my drill press to insert a tiny machine screw and pull the freaking thing out. I broke down and disassembled the tool, removing the nosepiece to try to get at the bit from the back. No dice.I called DeWalt tech support and asked them what to do. They said I could drive up to Sacramento and drop it off, or bring it to a tool repair outfit in the city.Brought it to my very competent tool repair shop who normally charges $20 for BS repairs like this. THEY tried for two days and finally said I have to buy a new nosepiece for a hundred bucks.What a joke. DeWalt should guillotine the engineering team who built a nosepiece that does not allow you to eject a short bit like any other impactor or screwdriver EVER DESIGNED allows you to eject.
Janaina Moretto
2025-03-17 13:21:41
Parafusadeira com torque forte e controle de torque ajustável, atende bem para montagen de estruturas metalicas, telhados etc.
Robert stairs
2025-02-15 09:36:30
The plastic circuit piece on bottom of gun moves around to much little bit of glue to hold in place but that's all dewalt guns
Customer
2025-01-23 10:26:13
Great price and product
Angela
2024-12-18 13:43:19
Excellent
Jesse James
2024-12-15 17:31:19
Love it
Recommended Products
