Your cart is empty.
Your cart is empty.Product Description
Professional contractors rely on DEWALT Self-Feed Wood-Drilling Bits when they need to bore holes 1" or larger for pipes, cables, and ductwork. Select sizes of these ultra-heavy-duty bits feature a triple-cutter design** that delivers long life, minimal binding and fast chip ejection. An aggresive self-feeding screw-tip pull the bit easily through the toughest materials. Standard 7/16" Quick Change Shank allows for fast bit changes in quick change ready tools like the FLEXVOLT 60V MAX* Brushless Cordless Quick-Change Stud and Joist Drill (DCD471) while preserving backward compatibility with chuck based non quick connect tools. * Maximum initial battery voltage (measured without a workload) is 60 volts. Nominal voltage is 63
From the Manufacturer
DeWalt DW1639 2-9/16-Inch Bit with 7/16-Inch Shank Selfeed Bit
Yb
2025-09-01 17:25:00
Used to drill holes in massive trees, did the job.Very satisfied.
Patrick V.
2025-08-10 10:10:03
Chews through wood. Had to use a fresh 9ah flexvolt on a Dewalt 445b to get this bit through 2x6 prime. Anything under 9ah caused the e-clutch to engage. Would buy again.
ed parslow
2025-07-10 11:44:27
What a amazing bit it cuts through two by fours like butter
Jen
2025-06-05 18:53:04
Worked well - would recommend it - just be careful of the amount of torque produced removing this much material.
Hector Anna
2025-05-07 14:11:13
I've used a lot of self bits such as milwaukee, Lenox, and bosch. This one is by far the best one I've had the pleasure working with. I have a heavy use of it since I work in new construction as a plumber.Update since: still a good bit but the fact that the price went up from 27 to 44 is a hard no for me now.
Bill
2025-03-19 12:59:01
This bit worked great for me... I used it to cut holes for plumbing in my garage. It lasted through the entire job, so it was very durable. A word of caution: if you are using it in a powerful drill (which you have to for this kind of bit), make sure that your are braced and holding it securely... if the bit catches, it can really hurt your arm. This bit was no worse about catching than any other hole saws that I have used of similar size.
Johnny821
2025-03-15 15:27:34
Drilled through some pretty thick stuff easily and quickly. Only complaint is a bit like this should be able to handle some abuse of running into nails. After drilling through about a foot of lumber, I hit some nails. Bit still drills through wood but not as easily as it did prior to hit the nails.
Richard N
2025-02-15 18:44:37
This is a great bit for drilling large holes in 2x4's, drywall and wooden planks. I bought this bit to drill large diameter holes into dead wood stumps and knots. This bit did not fare well in the tough world of drilling in a knot. I couldn't get it to bore in more than a quarter of an inch deep. This is no knock on the bit. I was trying to use it for an application that it was not intended for. I was hoping it would work and save me a lot of time. Hogging out a 2-9/16 inch hole in a tough knot is not easy. It takes drilling a lot of bore holes with a 5/16 inch bit and then hogging out the residue with a mallet and chisel. This process takes most of the day. I'll keep searching. Maby someday I will find a bit that can do the job.
Javf
2025-01-12 18:45:26
Great product and price
remo
2024-12-07 16:17:23
Good for the price
John J
2024-11-14 16:18:23
fast delivery. cuts well, but would not recommend. reason being the bit is NOT balanced. may be ok to use in a drill press but not good for hand drill. Also the centrer guide bit is too aggressive ( pulls bit too quickly into the wood).
Recommended Products
$36.99
$ 17 .99 $17.99
$27.83
$ 12 .99 $12.99