Shopping Cart

Your cart is empty.

Your cart is empty.

DYS F7 F722 Stack Flight Controller 30x30 AM32 65A 4in1 2-8S Brushless ESC for Freestyle FPV Drone Racing Drone Quadcopter (FC722 AM32 65A ESC)

4.6 (4) Write Review
Free shipping on orders over $29.99

$89.99

$ 43 .99 $43.99

In Stock

1.Color:Am32 65a Esc


  • Integrated 3.3V/5V/12V BEC ensures stable operation
  • Camera, receiver, HD/ analog two-in-one direct plug interface.
  • Using large solder pads, the pads are kept away from the components to ensure perfect soldering for beginners.
  • The flight control has four LED status indicators, which display the working status under different states.
  • Support Bluejay firmware, bidirectional DSHOT, and enable RPM filtering.


Product Description

F722
F722-2

Features:

FC STM32 FC722 Flight Controller

Top Features:

Improved circuit design, better components and lower electrical noise!

DJI HD VTX Connector (Plug-and-Play / No soldering required)

FC indicator LEDs for visual debugging

With LC filter

Specifications:

  • MCU: STM32 FC722
  • Gyro: ICM42688P
  • Barometer: BMP280
  • OSD Chip: AT7456E
  • Flash: 16MB (Blackbox flash)
  • UARTS: 6Prot
  • Motor outputs: 4x (SH1.0 connector)
  • I2C serial: SDA / SLA pads
  • Smartaudio / IRC Tramp VTX protocol supported
  • LED controller: Yes
  • Beeper pad: Yes
  • Firmware target: BETAFLIGHT
  • Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
  • Dimensions: 38*38 mm
  • Weight: 10.0g
  • BEC: 3.3V/1A; 5V/3A; 12V/3A

Wiring suggestion:

  • UART 1 for VTX HD / Analog
  • UART 2 for a Receiver
  • UART 3/4/5 for GPS or other sensors that require a serial port
  • UART 6 for ESC Telemetry

Tips

1. FC722 MCU has an inner inverter.

2. SBUS、CRSF、ELRS、IBUS、DSM ETC... can be connected to any unused UART_RX，we suggest you connect to Uart_RX2

3. Frsky SmartPort，Tramp & Smartaudio can be connected to any unused UART_TX，we suggest you connect to Uart_TX1

4. F.port can be connected to any unused UART_TX，we suggest you connect to Uart_TX2

AM32 65A-1
AM32 65A-2

65A 4-IN-1 ESC

Specification:

  • Supports: PWM, Oneshot125, Oneshot42，Multishot, Dshot150, Dshot300, Dshot600.
  • Firmware: AM_32
  • Mounting Holes: 30.5*30.5mm/Φ4mm
  • Supports 2-8S lipo input
  • Telemetry Output: NO
  • Current sensor: Yes
  • Constant: 65 Amps
  • Current rate: 200
  • Burst: 80 Amps
  • Weight: 15.3g
  • MCU: BB21
  • BEC: No

PACKAGE INCLUDED:

1PC X DYS FC722 FLIGHT CONTROLLER

1PC X DYS AM32 65A 4-IN-1 ESC

1SET X SILICON GROMMETS

1SET X WIRE HARNESS FOR F7 FLIGHT CONTROLLER


DJ Triple9
2025-09-03 20:18:18
First, the solder pads are butter. I was able to lay down solder without cranking the heat up, and no crazy residue or waxy scorched coating after I was done. Once wired up to my Sequire FC, it powered up and did its thing (pay attention to wiring, not all 8 pin FC to ESC wiring is the same). Telemetry is on point and current measurement needed no calibration.
Cooper
2025-05-30 11:24:49
This might be fine at lower voltages but it couldn't handle 8s at even 40 amps for a couple seconds as it is marketed.
E. Jensen
2025-04-26 10:43:57
No 4v5 pads DO NOT BUY IF GPS IS PART OF YOUR BUILD. This is a standard feature in modern FCs. Did not think that in the year of our lord 2025 I would have to worry about this being an issue.FC came with RX pads pre-tinned with large blobs of tarnished solder. Returned unit perhaps? Maybe they're just trying to be helpful but it seems sus.No verdict on the ESC yet, haven't flown the stack, but it hooks up to AM32 as it should and motors tested OK.
Nick W
2025-01-27 09:24:49
great for those 8S freestyle quads :)