Your cart is empty.
Your cart is empty.Product Description
Specifications:
- Function: forward, reverse, brake
- working voltage: 3.0V---9.4V.
- Diaensions(L*W*H): 35.0*22.0*6.0mm
- Current(A): 20A
- Driver frequency: 2KHz
- Input: Li-Po 2S / Ni-Mh/Ni-cd 4-7cell
- Constant current 30A Max 25A<30s Pulsed 50A<5s
- Brake On / with brake
- This ESC can work with 130/180/260/280/380 Brush Motor
- Size:20*20 MM
Package included:
2PCS RC-30A Brushed ESC Electronic Speed Controller w/Brake for RC Car Boat Tank
Robert M.
2025-08-05 15:03:41
I found this ESC to be perfect for my application in a vintage 25"tugboat using a 2 cell Lion (7.4V) battery and an RS380 motor that draws about 4 - 4.5 amps. The ratings on this ESC are all over the place (30A, 20A, 35W) I think 35W is the most accurate which puts the current draw at about 4.5Amps. I would not want to exceed more than 6 amps with this unit. In my case I removed the plastic heat-shrink jacket and epoxied a small heat sink to the 4 FETs for better heat dissipation and good long term operation.There are no instructions, not that it is very complicated, but it would be nice if the JST connectors were marked for Battery and Motor.For future reference:Female JST: BatteryMale JST: Motor
Allen
2025-07-31 18:14:44
purchased 6 in total. first two were good and worked as they should, next two were wired wrong at the futaba plug and on the board and would not work. i issued a return and got two replacements. the replacements were wired wrong exactly like the 2 i sent back. i sent a message to the seller about the issue to inform them of the issue. i wasnt even looking for them to replace them or even refund me. all i wanted was to address the issue on hopes they could correct it so that if i were to order more i would be sure to get working units. they sent me a long winded response explaining that the wiring was irrelevant and positive and negative can be either way. i would agree if it were the output to motor leads but it was the input to the board. you cant switch positive and negative on the input . anyhow 2 good units out of 6 is not very good and i do not recommend this product.
kenneth rood
2025-07-26 14:02:14
a advertised
John Yue
2025-07-16 13:22:37
They do work as expected. Nothing too fancy.
David freiermuth
2025-05-21 10:06:01
One malfunctioned in the first thirty seconds. Other one still working but will need to find something better. It's not a question of if it will go bad but when.
Billy The Kid :-)
2025-04-29 15:56:38
So i got these. To. Upgrade my crawler truck and my sons,. And. It seems to. Be working just find, i dijd notice my. Truck. Staying to take off by itself, amd cheked all my. Connection.,. Everyntijng and it still does it, tried to. Even [
William J
2025-02-16 10:13:33
As tittle reads. I got 4, and 3 failed within a week... with a 130 sized motor! .... utter trash!
heath brockway
2025-01-29 16:03:34
This is a brushed esc that is a simple plug and play design. The board is covered with heat shrink and is lightweight and takes up minimal space that works very well for dual motor setups. I used a single brushed motor (380 size). Gave good response with fairly smooth acceleration.
RenaissanceMan
2025-01-09 10:39:53
I bought several of these units now, they sofar all worked fine. I use them to control the motor speed and direction in lego trains, cars etc.
VITALII SULIATYTSKYI
2025-01-04 18:04:20
It’s not 30A. Burnt out in less than 5 minutes with 55T motor and 6.4 voltage.
Scott Schutten
2024-12-22 09:49:33
if youre looking for something reliable this isnt for you. it works good for testing your diy projects out though
Ricky Bee
2024-12-10 14:46:16
I was not sure what to expect. I installed it in a 1/18 scale buggy. It lasted about 15 seconds. It was boiling hot and would no longer go forward. It only had reverse. I am sure it would do fine for less demanding applications. I took a chance.
Recommended Products
$118.33
$ 58 .99 $58.99
$23.79
$ 10 .99 $10.99