Your cart is empty.
Your cart is empty.Fisch chrome vanadium metric 25 piece brad point drill bit set is great for normal drilling operations in soft and hard wood using cordless drills or drill press machines. Optimal drilling speeds vary from 2, 000 to 3, 000 RPM. This 25 piece set is the perfect place to start when you need a quality drill set that will get the job done and give you years of service. This handy set includes common metric sizes from 1mm to 13mm in 0. 5mm increments. The set is housed in a quality plastic stand case that protects your drills and puts them at arm’s reach when it is time to get to work.
Russell Bernhagen
2025-08-10 13:25:02
I had purchased an inexpensive set of brad-point drill bits from China and returned them. The brad tips were awful and the grinding inconsistent. These Fisch bits are excellent. The tips are sharp and true, and the grinding on each bit is accurate and consistent. If precision in drilling is a requirement, spend the money, get these drill bits and cry only once.
Robert Svoboda
2025-07-19 14:48:11
High quality drill bits for a very reasonable price.
Andrea P.
2025-06-21 12:42:26
I needed some metric sizes, so I bought these after reading some recommendations. It became painfully obvious I had never used any bits that weren't already worn and abused in the community shop, and weren't the ones I bought from Harbor Freight. They were straight, sharp, and cut wood like butter, effortlessly and without burning. I immediately requested the imperial version for Christmas. I did not get them- I'll have to gift those to myself.
Tom M.
2025-06-20 21:00:24
Drill bits are very sharp and seem to be of good quality. The bits are housed in a plastic case which was broken at the pivot point upon delivery. Probably happened in shipment.
rsl
2025-06-08 16:46:06
I've have a set of Fisch Forstner bits which were pricey, but worth every penny. So I got these brad point bits, which are also not cheap, but they cut cleanly into hard woods like teak or hard maple as well as soft and woods like cheap pine dimensional lumber. As a woodworker, I rarely have a call for conventional point bits, so these brad points have become my go-to bits. I first bought an imperial set, but liked them so much that it was worth the cost of another set for when I do metric work.
B. Hennig
2025-06-04 12:54:41
Well made and true to size drill set.
Bill D.
2025-05-25 18:53:28
Sturdy, well-machined bits. They come in a really high-quality case. I bought both metric and SAE sets. No problems drilling through oak, cherry, or maple so far. I spritz a bit of Blade Coat on them before using (highly recommended), then wipe them down before storing, and they don't miss a beat. I even absent-mindedly chewed right through a hidden backside knot in maple without a noticeable dip in the RPMs of my cordless drill. Take care of these bits and I'm certain they will last a long time. Really good bits.
Merchant of Venice
2025-03-20 15:24:59
I contacted Fisch about these. They said they were made in China but Quality Control [oversight] is in Austria. As someone else mentioned, any Fisch bits actually manufactured in Austria or Germany are stamped (on the shaft) indicating they ARE made in Austria or Germany. No stamp of where manufactured? Well, take a guess then, but Austria and Germany it aint.
Oskar
2025-03-08 13:40:11
Mycket stor skillnad på dessa och billigare borr
Customer
2025-02-26 15:32:36
first rate product
Bezigebever
2025-02-14 18:44:08
Drill ok quality plasic housing very bad quality I send it back
Herr Mützenhügel
2025-02-06 10:45:11
Einwandfrei! Laufen tadellos rund, die Zentrierspitze verdient ihren Namen und sie sind scharf wie verrückt! Aufpassen, wenn man sie aus der Kassette zieht, dass man sich nicht schneidet! Seit ca. einem Jahr in Verwendung, bestimmte Größen verwendet man natürlich häufiger, ich hoffe ich breche keinen der dünnen Bohrer ab, da mit einer Handbohrmaschine schon oft ein bisschen "wackelig". Zum Glück haben die dünnen Bohrer auch ein wenig "Flex", ohne zu brechen. Zur höheren Anwendungssicherheit ist bei dünnen Bohrern zumindest ein Bohrständer, besser noch eine Ständerbohrmaschine zu empfehlen! Sofern einer der Bohrer durch meine Unachtsamkeit abbrechen sollte, gerne wieder!!
Cliente frecuente
2024-12-29 18:04:26
Buen juego de brocas, muy surtido, opera con exactitud, solo creo que puede mejorar la artesanÃa, pero es una buena opción
Recommended Products
