Your cart is empty.
Your cart is empty.For residential garage doors- normal 7' and 8' tall doors with torsion assembly. Sold in pairs: 1 right, 1 left.
Connie J. White-Buckley
2025-08-07 12:38:19
made my garage door work so much better. Thanks
TL
2025-07-09 10:06:47
Strong steel and good bearings for torsion rod. Easy to install. Multiple holes for versatile installation options.
Hallo
2025-06-29 12:38:47
My Duralift DLK16 kit comes with 2.4 thickness end plates so I replaced them with these. These are much more studier and aligns perfectly with Duralift flags. Not sure how Duralift screwed up their design, both end plates are exact same size but this brand aligns perfectly while Duralift own plate does not, weird. The bearing is definitely sleeve, just like Duralift . As a matter of fact, just about all the bearings on the market are sleeve. You can just shake them right out of the box and hear them plays - not good. So I just finally ordered a Donepart ball bearing1641NR-2RS, these 2RS have 3x the rating of standard sleeve bearings (1250lb vs 400lb static load). And it's the only one I can find that comes with snap ring so it locks in place. Fingers crossed let's see how it goes. For those of you who wants to know how to remove the bearing, it's not hard. There are multiple ways to do this. Best method is using an HF hydraulic press. Me I just use a 6" vice to remove and press them into place, you can just buy an HF hole cut kit for a few bucks, make your own sizing out of 2x4 and apply to the vice. Let's wrap it up it is imperative you replace these Chinese made sleeve bearing - yes, they're made in China but the plates are assembled in Canada. These sleeve bearings will eventually freeze on you in a few years, knowing this project is a pain you'll need to do it right the first time so you can forget about it. Don't forget to take your time, make sure everything is properly leveled and even, slow is fast :)
KMB
2025-05-15 14:35:26
Replaced broken springs and decided to replace the end bearings, which come complete with plate flange. The flange's universal application was helpful. One side retrofitted without problems, however the opposite side needed a little elbow grease to get it to fit properly. The flanges seemed identical except for having right and left application. Once in place worked very well. Still happy with this item and would purchase again.
AJB
2025-04-26 17:29:46
I got tired of having to replace my EZ-set springs every 3 years so decided with the help of a youtube video to convert my EZ-set torsion springs to regular torsion springs which will last a LOT longer and were much cheaper than the manufacturer replacement every 3 years. These were part of the complete kit of pieces needed and all arrived together, and have been easy to fit and work perfectly together to open and close the double garage door multiple times a day and hopefully for many years to come.
The Newokie59
2025-03-15 11:14:03
These end bearing plates are better than the OE that were installed years ago. The extra tab at the top will prevent the plate from flexing and causing a bind situation. The quality is very good, the plate thickness is thinner than the OE style. The top tab more than makes up for that. The bearings are filled with grease and the movement is very smooth. The finish is OK. None of the edges were deburred or softened, which is a cut hazard. 5 minutes with a file took care of that. I am sure these plates will give years of service and I am very happy with my purchase.
jeffrey l blancett
2025-01-04 18:10:15
Used it for roll up door on 10 x 20 storage shed I built
R. Sharma
2024-12-25 15:31:12
If you are going to be changing your springs it’s worth while changing these too. It only takes 5 minutes extra during the process to install these (4-5 bolts to undo-redo. The part is stamped Canada, so I guess it is made in canada? This was an exactly match for what I had. My old bearings were sealed, and pretty dry. These new ones are silent. I’ve heard these bearing seizing so why risk not changing them when they are so cheap? The hardest part was separating the 2 parts from each other, the 2 plates were stamped from a single peice of metal and you have to bend them and flop them around to snap them off. You also have to be careful as now there are some spot with burs.
Recommended Products
