Your cart is empty.
Your cart is empty. How to identify My Model Number?
Check the back of tablet, make sure the model number is: K72LL3 or K72LL4
-Kindly Note:
This item can fix your scratched/broken Touch Function (Digitizer).This screen kit is not compatible with Kindle Fire HD 8 2022 (released in 2022).
We have provided a tutorial video on the Amazon product page. Replace the screen after watching the video.
-Notice:
Only fit Kindle Fire HD8 10th Gen
Package Includes:
✔ x1 Kindle Fire HD8 10th Gen Touch Screen Replacement
✔ x1 Double-sided tape
✔ x1 Microfiber Cloth
✔ x1 Prep Pad
✔ x1 Screwdriver
✔ x1 Metal Spatula/Scraper
✔ x1 Strong Suction Cup
✔ x4 Triangle Opening Tools
✔ x1 Pry Opening Spudger
✔ x1 Black Spudger
MacDaddyBighorn
2025-07-31 18:51:59
Screen works great, I replaced my kid's cracked screen with one of these. When I was testing it I noticed one strip on one side wasn't sensing touch (95% of the screen was) so I emailed customer service and they refunded me without issue. It could have been a defect or install error, but they didn't care. I ordered another one and installed and it worked perfectly.The kit comes with all the stuff you need. I would have preferred a thin metal pry tool instead of a razor blade, but they work all the same. I recommend you use heat to remove the original screen, it is really stuck on there!
tjm
2025-07-17 15:56:57
There is really nothing to dislike about this item. It was a perfect fit, the tools worked when complemented by my own top quality tools and the adhesive tape worked perfectly. Installation is not for someone with no patience, and maybe no experience with similar jobs. There is the possibility of doing damage while removing the old screen using a real heat gun and be sure you understand how the ribbon connectors are released. A suggestion would be to completely cover and seal the old screen with some clear packing tape to avoid broken glass flying around, especially if the screen is already cracked. These touch screens appear to come with a protective film on BOTH sides of the screen that may be clear or slightly opaque so may sure you take both sides off. The reason I say this is because one reviewer complained that the screen was not as clear as the original and I suspect he/she did not remove both protective films.
Kayla
2025-07-01 17:03:07
The media could not be loaded.
dictoresno
2025-02-23 16:28:46
My son cracked the digitizer on his Kindle Fire Kids 8HD. Bought this as a replacement and it worked perfectly. As stated before, there are no instructions nor any decent how to videos. I had to rely on mostly my own intuition and experience to reverse engineer how it would assemble. If you've ever replaced an iPad or phone digitizer, this will be mostly easy.The kit comes with a tool kit that has all the tools needed. Once I saw the replacement adhesive tape, I knew my handy soldering/heat gun station was going to be used. If you dont have one, you can use a hair dryer but it will take longer. If you have a soldering/heat station....this will be easier.1. Use the guitar picks and long spudger to unsnap and separate the rear casing from the internals.2. Flip the innards over and you will see on the new digitizer where the corresponding ribbon cable is on the PCB. the ribbon cable slides into the connector. Use the tweezers to flip up the small black catch on the connector to unlock the ribbon cable and then unplug the battery cable from the PCB.3. using the small Philips screwdriver, unscrew the 5 or 6 screws that hold the PCB to the frame. This is to allow enough room for the ribbon cable to be thread out of between it and the frame. The hole is smaller than the cable, so use a spudger to wiggle some room later.4. using a heat gun, start heating the outer edge of the glass digitizer, loosening the adhesive. slide the guitar picks along the edge as you go, separating it from the frame (this leaves the screen untouched underneath).5. once the digitizer is separated, pry the ribbon cable out (using quick heat on the processor on the ribbon cable as its glued to the PCB with adhesive) and remove the digitizer completely.6. remove excess remaining adhesive out from around the screen frame and lay new adhesive strips.7. remove the protective film on the inside of the digitizer and thread the ribbon cable back through the housing.8. using tweezers, remove the adhesive backing on the strips and carefully lay the screen down on the frame, pushing into the adhesive all the way around and making sure its flush.9. flip it over and adhere the ribbon cable to the PCB, slide the cable into the connector and lock it in.10. at this point you can plug the battery back in and test your work, making sure the digitizer works properly.11. replace all screws and then snap the case back on....youre done.
Vanessa
2025-02-15 15:35:08
The tools the package comes with are very flimsy and broke before I could finish. The first replacement did not work either. After contacting the seller by email, I was issued a refund within 24 hours. They stated it was a faulty product and I could reorder a new one if I wanted. I decided to order a new one and try my luck a second time. Luckily, it worked! I watched a few YouTube videos and used a hairdryer to help.Time consuming (1 hour tops) but totally worth saving $70 to have it professionally replaced.
astroturtle
2025-02-13 15:54:23
Be careful which video you view for replacement. This is the glass only and most videos will show complete disassembly for lcd replacement as well. Mine didn't work on first assembly and the seller was going to refund money. Turns out the lcd ribbon (not part of purchase) was not making good contact. I worked with ribbon and got it to work. The glass was perfect and I have my HD8 working again. Be sure to push the lcd ribbon at the left lower part of motherboard completely in gently so as not to damage the cable.
Customer
2024-12-29 12:54:02
I wasn't sure I could replace the glass on my daughters tablet on my own but I gave it a try and it worked. I watched a video on you tube and just followed the instructions. Easier than I thought it would be.
Snozcumber
2024-12-23 17:24:54
The nice bits are this comes in a nice box and pretty much everything you need.However, firstly you’ll need to explore YT to find a guide on what to do as there are no instructions.Secondly, the tools are utter garbage and will be broken within 10mins and way before you are even half way through this process. Unforunately the lever tool is the most important tool and it snaps straight away.The final issue for me was there was a line on the replacement screen, however as there was a protective cover I figured the screen would be ok. Sadly not, and after full install when you remove the plastic cover the line was still visible.There is a lovely card that comes with this about good or bad feedback. I emailed them as per instructions to whinge about the crap tools and screen. They were apologetic and offered a £7 refund on a £28 product.I declined and said I’d leave a review instead..Yes, I’ve replaced the screen. But, the screen is damaged and there is now new damage to the casing where I had to improvise with household items when the tools I’m supposed to use broke.
Recommended Products
