Your cart is empty.
Your cart is empty.Product Description
3 YEARS PRODUCT SERVICE
If there is any problem with the fuel injector tester, please let us know. Don't worry! We will send you a replacement.
Short Pulse Mode: Output a pulse, pulse width is 255 milliseconds;
Medium Pulse Mode: Output 50 pulses, pulse width is 7 milliseconds;
Long Pulse Mode: Output 100 pulses, pulse width is 3.5 milliseconds;
Continuous Pulse Mode: Output 50 pulses every 1450 milliseconds, pulse width is 7 milliseconds.
Suitable for all 12V and below injectors, including FSI, EFI, GDI, MPFI, SPFI, TBI, CFI, L-JET, LPG, K-Jetronic, coil-type direct injection injectors. Compatible for cars (VW, Audi, Ford, BMW, etc), motorcycles, boats and ATVs injectors, etc.
2 POWER SUPPLY METHODS : a 12V vehicle battery or an external DC 12V (recommended at least 1.5A) power supply.
Curt M
2025-08-25 10:50:39
Very complete set of injector adapters. The two injector drivers allows side by side comparison between injectors.
John Long
2025-07-11 11:20:25
Pretty good injector exerciser/ cleaner. You do not have to remove the injectors for the first pass if the car has been sitting for some years. Just pull the electrical plugs and then apply this to the injectors one at a time and if they barely make the buzz or not at all then you can pull those injectors first.The only improvement I would make is to make the holes, at the bottom where you put the cleaner fluid, a slight taper so that they can accommodate all the differing brands of cleaner as some will fit and others will be too small to seal. Or take it with you to the parts store and find a cleaner brand that will fit.
Fredco
2025-07-03 12:22:13
Fuel, especially older fuel picks up all sorts of strange particles and that clog or block your injectors. This is a great kit to exercise and clean out your fuel injectors easily and quickly. Great maintenance tool or to have around if you experience trouble. Even if you use it once, the savings over a service station or a new injector makes this a great deal and a fast way to cure one of the most common problems
Chad
2025-05-20 15:24:04
The hole on the plastic fitting doesn't fit carb cleaner can. Had to create my own adaptor to fit tightly.
Lawrence
2025-05-09 18:19:35
This tool works great in some ways. My motorcycle has quote a few miles on it now. Throttle response hasn't quite been what it used to be. Well, new fluids and spark plugs, valve shims checked, chain clean and greased, and sparkling clean fuel injectors... we're doing great again.This cleaner is pretty easy and intuitive to use. You can see the results in real time. A chunky stream gradually spreading out with a more finely particled spray. It is actually kind of fun to use. If it wasn't so hard to get to most fuel injectors, I'd happily clean all of my friends' injectors as well.A couple things I'd change... I'd like a larger taper where the seal needs to push into the feed tube housing. It was a bit tougher than it needed to be to push the injectors in. Also, I wish that the feed tube itself was bigger. The housing is reasonably large, but the inner feed tube is rather small in diameter. However, the tube is too loose to fit my cleaning tube nozzle and it doesn't fit the nozzle coming out of the actual can either. The only way it was able to reliably add cleaning fluid was with a small plastic bulb. If I didn't have that, it would have been a different review. I hope the company identifies the near miss and makes some changes on future iterations. I may end up 3d printing a new feed nozzle for it. That would definitely make it feel like a better value.
axlec
2025-04-08 17:38:22
The tester itself works great, it's easy to use and gives enough options to get what you need done. The problem with this kit is the plastic tubes that you are supposed to be able to use to connect your injectors to and your cleaner to. The injectors fit into the plastic fine, but when you try to put the can of carb cleaner into the other end it won't press the stem down and therefore you can't get any cleaner to come out which makes the adapter useless. I made my own adapter with a piece of rubber hose and a plastic lid with a hole punched into it for the straw of the carb cleaner to go through, using that setup the main unit worked great.
Brian Jones
2025-04-04 17:57:01
But the electronics work fine. I just use carb cleaner while this pulses the injector. Gets the chunks out. Good enough for my needs.
Brad Icke
2024-11-14 17:21:24
The media could not be loaded.
Recommended Products