Your cart is empty.
Your cart is empty.Fits 3/16" (5mm) Hole Panel Range (grip) 1/8" - 15/64" Flange Size: 15/32" Replaces GM: 20432975 VW: 175-853-57701C Chrysler: 6503800 Ford: N804343S Fits 3/16" (5mm) Hole Panel Range (grip) 15/64" - 25/64" Flange Size: 15/32" Replaces Chrysler 6500898 Nylon Blind Rivets 1/4" (6. 3mm) Hole Size Panel Range: (Grip) 3/32" -3/16" Flange Size: 1/2" Replaces GM # 20421672 Fits 1/4" (6. 3mm) Hole Panel Range (grip) 5/32" - 13/32" Flange Size: 1/2" Replaces GM # 10184895, 20452072, Ford # N803862-S & Chrysler # 6501559, 6506007-AA Fits 17/64" (6. 6mm) Hole Panel Range (grip) 3/32" - 3/16" Flange Size: 45/64" Black Nylon Replaces G. M. # 20433026 & VW 175-853-577A Fits 1/4" (6. 3mm) Hole Panel Range (grip) 5/32" - 13/32" Flange Size: 43/64" Black Nylon Replaces G. M. # 14063981, Ford N803043-S & Chrysler 6500911
Customer
2025-08-10 15:45:33
Removed the inner fender well of my Jeep to replace a pain in the butt PCV valve on the back of the motor. The only access to it is to remove the passenger inner fender well . The factory plastic rivets have to be drilled out to remove inner fender well. When finished , the plastic rivets made it look like I never removed the panel. The kit has various sizes for a lot of different vehicles.
Michael
2025-07-03 12:58:30
These are perfect for replacing push pins for a more permanent fixture. Easy to drill out when necessary and they hold together well. No issues at all with these.
Ðmazon Customer
2025-06-24 17:47:21
Works good good price. Not high end but I didn’t need high end I just needed the tools to work
gerry
2025-06-13 12:21:12
perfect fit
Timothy Warren
2025-06-08 11:17:03
The studs on the plastic rivets get stuck inside the tool every single time. You have to tear apart the tool after every one that you do. The rivets they also send just shatter if it is cold. This kit is garbage.
John f.
2025-06-06 14:24:03
Worked perfect on my fender well. Perfect size rivet gun worked good
Majik
2025-04-22 14:18:48
So I bought these for my 98 Volvo s70 (white block) for the wheel well mud flap at the front. The ones from factory were metal. Some were missing when I got the car. From factory I needed 4mm. Well good thing I got a kit with different sizes. Once I got the ones that were broken out. I was able to use those 6mm for the larger holes and smaller for others. Never used a plasric rivet till that day. They work as intended. Wouldn't recommend for something you need to have high strength. But for trim pieces that aren't under pressure work fine. I also didn't use a rivet gun. Just a tool to hold the rivet in place and a pair or needle nose to pull the center pin out. Would buy again if I need more. Honestly I don't see me using all of these. Lol
Sherman B.
2025-01-31 11:48:35
Seems like they are adequate... but they didn't impress me to the point of 5 stars. Will I buy them again? Yes, I will... I mean they are just rivets! And the exist out of sight!
Mr J.
2024-12-25 09:19:48
The sizes are wrong. They vary 1mm so the 5mm is actually 6mm
Recommended Products
