Your cart is empty.
Your cart is empty.The Hi-Lift Jack 4XRAC Jack Mounting System is designed for serious off-roaders looking for an easy, inexpensive way to stow a Hi-Lift jack in a convienent, secure location. Each kit contains two mounting brackets, two mounting bracket caps, velcro securing strap and all necessary hardware.
jamie j
2025-08-31 17:23:15
Nice way to mount your jack and has a way to lock the jack on so it won’t get stolen easily.
muley505
2025-08-15 15:44:15
This product installed easily on my 99 Jeep Cherokee. I drilled the 8 holes needed for installation in the front bumper, and wiggled my hand up in behind the bumper with an open-ended wrench to get nuts on the end of the bolts, had a helper run a ratchet on the outside of the bumper to tighten the bolts down, and it was good to go. I like it mounted to the front bumper because it's out of the way and slightly counterbalances any weight I put in the back of the vehicle. It mounts a jack very firmly while still allowing it to be easily removed when needed. I also like that I can put locks on the jack to keep people from stealing it when I'm out in the middle of nowhere. This product works very well for its intended purpose, and can be installed in about 15 minutes depending on where it is mounted. Very satisfied!
mkj
2025-06-21 15:13:09
They are rock solid and work as intended.I have one major issue with the product and that's the paltry hardware kit.The screws need to be longer, it needs to come with more flat washers and more lock washers. In addition 2 more of the mounting caps would be nice. One underneath and one to go over top of the lift. Seems to me it would secure it better and give it a nice finished look.Can't imagine that you would want to mount the brackets without using at least a flat washers on each side.Only other issue I ran into was finding a good place to mount it. I wanted on the bumper but not in the way of anything. Unfortunately the stock Jeep bumpers are, for the most part, all plastic. So for my taste the best I could do was put it on top of the front bumper.I love where it is mounted and I am overall happy with the product
PracticePiety
2025-06-18 16:12:58
I first made the mistake in buying the Loc-Rac mounting system first which I returned to get this. I looked at this product so it would be secured and locked and not pay $60. I have in mounted behind my window in the bed of my truck and it works great. After its in and the jack mounted there are 2 places to insert a lock to deter lazy theifs from stealing your precious jack. It comes with decant instructions and all hardwear required. A WARNING to all who buy! Measure 2 twice and then measure again especially if you did mount to the floor of your bed where the surface is uneven. There are supporting brackets underneath your truck and if your not careful you will be drilling unnecessary holes in your vehicle and no one wants that to happen.(Didn't happen to me Thank God) Or the jack will not fit properly and you'll have to enlarge on of the holes in the jack so it slides to the bottom (that did happen to me lol). Which it didn't turn out bad at all because it was one of the upper most hole and I won't be jacking that high with the jack. I got lucky!So just be careful!
priley
2025-06-12 14:18:50
I was able to install this on my 1981 Jeep CJ-5. I thought it would be pretty easy, but it didn't line up with the bolts on the rear frame. This left me with the choice to either drill out the bracket, drill out the bumper, or weld it on. I decided to use the metal glue gun. :)Unfortunately, I had to install my Hi-Lift Jack upside down, due to the space between the bumper and the wheel mount (31" tires). This meant, I had to create a way to hold the handle to the jack so it doesn't hit the ground.Honestly, it is a bracket. Pretty much some customization will have to happen, especially on a 40 year old Jeep. I do like the how the "clamps" hold the jack in place. That is well designed, but some fabrication might be required.It does sit very nicely against the rear of the Jeep. No worries on hitting it while going 4x4'ing.
Rick
2025-04-20 12:18:33
Great for mounting my high lift jack horizontally and securely. Very well made and heavy duty.
The Ritchies
2025-02-17 18:30:24
Solid mount. The spacing of the mounting holes works with mollie panel but does can be finicky. Great for truck bed mounted panels.
Joey
2025-02-08 12:58:21
I mounted this on my 2008 Chevy Silverado front bumper. Since the Silverado bumper isn't flat and the bolts are a little cock-eyed once mounted, I took a sledge hammer and straightened the 1/2 bolts that hold the actual jack in place. You have to hammer the bolts with the wing nuts on so you don't damage the threads. Try not to hit the threads. They're solid. The jack doesn't move. Makes a nice platform for standing (on the jack) if you want to do some maintenance/work on your engine.I thought about mounting these on the hood but decided against it. Where it's mounted has multiple pluses. One of those being that all my work is in the city and there is very tight parking. Cars are always bumping me when they parallel park. With the high lift mounted to the truck bumper, now they'll think twice about bumping me. I have a 6 inch lift and the height of where this is mounted and how far it sticks out is right about trunk level on most cars. It puts a smile on my face thinking about people parallel parking in front of me and trying to do the bump and this puts a nice dent on their trunk. On the rear I have a pintle hitch attached. No one has bumped my rear bumper ever since I put it on. Now I'm protected from jackasses on both ends. :)We'll see how it holds up when I drive across the country, through Baja California and the deserts of the Southwest for a month in August. Will post a follow up.
Gilberto g.
2025-01-25 10:24:26
Excelente producto lo puse en la caja de la camioneta y quedó muy bien y sin batallar, llego en tiempo y forma
Aj boughen
2024-12-05 20:41:28
I’m really satisfied with this mount. It’s simple and clean. I would definitely recommend it. Installed in under 45 minutes. I mounted it to my trucks tool box. I would recommend a backing plate if your putting it on thin material like my tool box.
Lisa F.
2024-11-21 09:12:09
My farm jack is mounted to my truck tool box with this system. It works perfectly.
Customer
2024-11-20 15:17:55
Just what I need to hung my hi lift
Jordan
2024-11-16 18:30:13
Nice quality
Recommended Products
