Your cart is empty.
Your cart is empty.Product Description
Installation Instructions:
- Turn off power to your dishwasher in breaker box (Absolutely Critical To Avoid Shock)
- Rotate lower access panel fasteners and remove them
- Remove access panel/sound dampening pad. Determine if the water supply or power lines have enough slack to move the dishwasher. If not, you will need to turn off water supply valve, disconnect water supply line from inlet valve & release power line from junction box
- Open dishwasher door, remove the screws from the existing brackets (if present)
- You will next be moving the dishwasher. To do so, you may need to lower the dishwasher by adjusting the leveling legs
- Carefully pull dishwasher a few inches away from the front of the cabinet
- Use pliers to pull up tabs in back of the bracket (if present). Pull out old brackets
- Insert new brackets. Use pliers to adjust the back tab to lock the brackets in place
- Slide the dishwasher back into the cabinet (readjusting the leveling legs, if necessary). Replace the screws in your new brackets
- Reverse steps 3, 2 and 1.
travis mullins
2025-07-16 10:10:49
Works like a charm
Dawne Short-Scott
2025-07-14 11:49:31
My originals were missing and these fit perfectly and now my dishwasher stays in place.
Devon steed
2025-06-26 13:32:42
Worked perfect for me. Got a dishwasher from a friend since he got a different one. Took about 2 minutes to install. Nice product
Evan Brown
2025-06-23 16:10:47
I bought my dishwasher on markdown from Lowes, it was a scratched return. Originally, it was around $4,000, but I bought it for close to $500. It didn't have any hardware, (not a big thing), but I didn't even know that there was such a thing as mounting brackets, until I watched a video on how to clean the filter. Long story short, I bought these, and they are a little thinner that I would expect, but strong enough to hold up a full dishwasher. They "could" be a little thicker, even if you had to bend them to shape them in order to properly secure and install them, they seem (to me) on the (slightly) thin side. They do work, and they are a long way from having nothing at all (Like I did). I just hope that they continue to last for years to come, (which they seem very much like they WILL).
TheEducedGentleman
2025-06-21 13:32:38
The media could not be loaded.
Scott F Blaisdell
2025-05-04 15:12:53
Good price. Easy installation
Honest Abe
2025-04-20 13:55:13
I used these brackets to secure an older (Frigidaire) dishwasher to my kitchen cabinets after installing granite countertops. The Frigidaire dishwasher was an older model and as such was not fitted or designed in any way to be used with side mounting brackets. The dishwasher had brackets but they were welded to the top of an aluminum band which was on the exterior of the dishwasher and which held the plastic dishwasher body to the metal dishwasher door frame. But I couldn't use these brackets since you cannot screw into granite without possibly damaging it. However, even though there was the aluminum band which went around the dishwasher exterior, there was absolutely no where to "hook" a bracket (you also could not screw into the aluminum band because you might puncture the plastic dishwasher body which would cause leaks and trash your dishwasher). So I purchased these brackets and J-B Weld 8265S Original Cold-Weld Steel Reinforced Epoxy - 2 oz. I mixed the epoxy and put a healthy amount on that aluminum band which I described above. I then stuck these brackets in that epoxy and used blue painter's tape to hold the brackets in place. I let the epoxy fully cure (15-24 hours) and then I tested. SOLID HOLD. Just like a a steel weld. I pushed the dishwasher back in the cabinet and used 1/2 inch wood screws to secure to base cabinet frame. The other side was next to a sheetrocked wall so I used 4 inch screws and found a stud close-by and screwed the bracket directly into a stud. Mounting now is solid as a rock. Dishwasher does not move at all. Hope this helps. Good luck!
Chris S
2025-04-13 15:46:59
Ordered these after I thought the instructions said to break the tabs off of the OEM brackets. WELL that's only for side mounting, not mounting to the countertop. These were near exact replacement. NO SCREWS, which is fine. I wasn't expecting to get any since there aren't any pictured. Buy these instead of spending $20 to get the OEM ones. If you're working on this and not calling a technician, I'm sure you have some screws laying around that you can use.
Nicholas Trudeau
2025-03-25 17:13:47
Just as shown
Jaime Heredia
2025-03-12 11:17:48
lo que se necesita para una lavavajillas Maytag
Mark
2025-02-16 09:53:22
Le faltaron tornillos para sujetar a la lavadora
Customer
2025-01-29 16:32:36
Yes they were compatible and they fit
Recommended Products