Your cart is empty.
Your cart is empty.Michael R
2025-09-03 11:37:34
Theses are made really nice and have a great weight to them. I did have to bore my hole 1/2 mm for them to fit, but I knew that when I bought them. The RC car stickers in the package was a really nice touch. These are definitely a great value!
Alexander K
2025-08-31 10:23:37
I bought a nice set of wheels and tires for my basecamp. After spending the hour to put them together I realized that the new headlock wheels could not snug all the way up because of the portal axles. Went back to the local hobby store and bought 6mm hub extenders and that didn’t work either. So I snagged a set of these hoping it would do the trick plus add some weight. The lock but wouldn’t fit inside of the wheel hole so I drilled it out, 11/64th I think. Fit like a charm and so far has taken a ton of abuse. Good product got some free stickers too
Dennis
2025-08-24 21:20:16
The wheel hex nuts are made of good brass material. For most RC trucks other than crawlers and straight axle models. The bore is to small and if used on a basher 1/10 scale. You’ll most likely have to bore out the center, it's not difficult at all. Also, the axle pins are small in diameter. They are not made for anything with a higher torque so it would be prudent to use the OEM axle pins if your planning to drive faster than 35 mph. You can widen the grove on the extenders with a dremel tool. My last caution is that the nuts that come with these extensions may be short, so if you’re using oversized wheels and tires, you’ll need longer axle nuts, check the chart on the product page to make sure they fit your model. Theses extensions may require a bit of customization, but in the end, it's worth it.
Mark Withrow
2025-07-07 14:13:04
These extensions are easy to install, and do their job well. Just be careful when tightening the new 8mm lug. You can potentially snap the crosspins if you make it too tight.
Kenneth Hogard
2025-06-15 19:02:02
They fix perfectly on my hyper go h14bm.
Margaret Ryan
2025-06-11 17:36:14
I have to machine them to fit the H14BM as they dont slip over the hex pins. They'll probably fit my 14301 perfectly, but that was not the intent of them. They'll probably be great afterward.
cogswell
2025-05-09 15:51:13
For the most part their products are great. No complaints. These are as simple as they come. Good fitment, no hassle. The nut is actually an 8mm, rather than the usual 7mm. I had a wrench from an old nitro car that works for it, because my wheel wrenches did not fit the 8.
john spevak
2025-04-11 11:21:13
Axle extenders were a perfect fit! No drilling, slide right on! All the required pieces were in package! Gives my gen 8 scout a great look now! 15mm was just right!
Steve McNeil
2025-02-22 20:15:40
I bought these to give my rc truck a better stance and feel and they work perfectly
James
2025-02-05 15:43:23
if your looking at getting bigger tires on a rc these are needed put on a 1/16th size car and work fine.
オミーズ
2025-01-13 15:06:11
好ã¿ã§ã™ã
Placeholder
2024-12-08 10:14:50
Scrue just broke while tightening. Received call for review and when I explained to her she said will check and get back but never called me again.
Ein Konsument
2024-11-28 12:32:34
Optisch hochwertig und leicht zu montieren. Man muss allerdings die Bohrungen von den Felgen erweitern, weil die mitgelieferten Schrauben aus technischen Gründen einen größeren Durchmesser haben. Das sollte man bei seiner Planung mit einbeziehen. Ich kann das Produkt empfehlen.
Recommended Products
