Your cart is empty.
Your cart is empty.Product Description
Homesteading Momma
2025-06-20 15:01:40
I knew we’d have a bit of trouble with assembly. Easier with 2 people. We used the paper directions alongside the YouTube video and it wasn’t too bad.
Klutz Master
2025-06-19 12:59:25
Good value. Well-built and steady under pressure. Few annoyances such as the open/close jaw handles are opposite (righty/loosey; lefty tighty). The latches for pulling up the jaws should have spring-locks—a bit of gymnastics to operate. The cross-members should be a heavier gauge. The rubber feet take a bit to get on and a few seconds with a heat gun will help. There is no latch/lock for the legs. They simply fold/unfold. Hasn’t been a problem but wonder long term.All that said for the price they are an excellent value by comparison Needed to replace ancient B&D Workmate but the new ones (save the highest priced unit) do not offer value. Others of this type have their issues as well. This unit is not a commercial grade product but perfectly adequate for garage jockey.
Fang
2025-06-12 12:11:56
The workbench is very convenient and versatile, the height can be adjusted, and the table can be moved. The design is very reasonable.
Doug
2025-05-09 14:13:01
First thing to do. If you have a 1/4 metric drive set and a 10mm/13mm open end/box wrench, take the cheap combo 10/13mm box wrench and throw them out! Admittedly, it is good they were included for those without a better set of metric tools, but for those who do have tools....Instructions could definitely a lot better, and are sort of needed since the illustration is worthless. My suggestion to the manufacture is just include an exploded view of the table, a good list of parts, and some minor notes in writing where needed.The hardest thing was placing the bolts though the brackets then through the two holes; one on each side of the square leg when one or two of those holes were just a bit off center from each other to cause some cussing. Most were ok, but those not....PITA.Playing with it for a short time, the table moves nicely up/down and height not bad for this 6'2" guy. Table tilting might be a nice feature, I can't think of when I would use it, but it is there and moves freely so I guess good to have. The cranks move the one table top piece back and forth nicely (smooth) and the other one has a lot of different locations to all for a good spread between the two, or a tight fit for nothing to be placed in the middle.Yellow sliding blocks appear to be ok.I have not actually used this table yet, but have no fear it will do just as good as a 13 year old B&D woodent table it is replacing.I will add, time will tell if all those bolts/washers/nuts will need lock washers. Over time, if moved around a lot and with a lot of use, I can see those nuts loosening up. If they do, about 22 lock washers are cheap and won't take long to add to each fastener.I gave it five stars (four for assembly) and if it does what it is supposed to do for me, I'll leave it at that. If not, (as noted by Arnold) I'll be back.
Giraldo Nieves
2025-04-19 18:05:21
Me acaba de llegar y ya estoy comprando otra igual, la promoción no le hace justicia a este banco de trabajo y no se explican algunas ventajas que vienen en el manual pues se pueden configurar de muchas formas incluso si tienes más de dos.La construcción se siente muy fuerte, con materiales de buena calidad, no es un banco tradicional de carpintero pero aún asà espero dure mucho tiempo, tampoco tiene un precio que haga pensar que sustituya al banco tradicional.Sólo tenga paciencia al configurarla para trabajar o guardarla, no querrá verse con las dos manos pellizcadas entre las patas sin más ayuda que la frente para soltarse, espero que no me ocurra otra vez lol, ya les dije que es fuerte.La primera que me enviaron se dañó en el envÃo, el vendedor se puso en contacto conmigo para informarme y preguntó si querÃa otra o la devolución a lo que respondà pidiéndole otra que me llegó en menos tiempo que la compra original, la comunicación con este fue rápida y eficiente, no puedo más que agradecerle por su dedicaciónLa recomiendo totalmente, es perfecta.
Caldesjv
2025-03-23 15:00:52
It isn't a bad little work table, bu it came with surface rust on some threads. It also was a bit more difficult to put together than it needed to be. A few changes would have made this go together in 30 min instead of an hour and a half. Other than that though it works well and seems pretty sturdy so far.
Joe Carroccia
2025-02-27 13:00:51
Perfect size, weight and easy to use. I would recommend this bench to anyone. Only down side is there's no carry handle for it
Mike
2024-11-17 11:24:26
It's a bit confusing at first to release the top for storage, mechanism goes down in both directions.
Recommended Products