Your cart is empty.
Your cart is empty.Package includes:10pcs APMT1135PDER Carbide Milling inserts +1piece 300R C10-10-120 Milling holder + 1piece 300R C12-12-130 Milling holder + 1piece 300R C16-16-150 Milling holder +3pcs T8 Wrench 300R C10-10-120 Milling holder: Overal length:120mm/4.7inchShank dia: 10mm/0.4inchTip dia:10mm/0.4inch1 blade devices300R C12-12-130 Milling holde: length:130mm (5in) , shank diameter:12mm (0.47in), Tip diameter:12mm (0.47in),1 Blade devices (1 flute)300R C16-16-150 Milling holde: length:150mm (6in) , shank diameter:15mm (0.63in), Tip diameter:15mm (0.63in),2 Blades devices (2 flute)APMT1135PDER Carbide milling inserts: balde length:11mm, design for Steel, Cast Iron and stainless steel Good for shoulder milling, face milling and slotting
Kindle Customer
2025-04-20 17:38:07
These are very nice. I cut mine down because I run them in a small bench mill.
shawn brown
2025-02-25 18:36:00
This ia a very nice set of milling tools. They come with extra tips and at a great price.
Liz
2025-01-26 16:46:55
I was leery about the single cutter but thought I’d give it a try anyways. Maybe I was wrong? I wasn’t. I should have stuck with my intuition.I wanted to have some carbide cutters for the odd mill scale covered or harder than normal metal piece to be machined without immediately ruining a normal HSS end mill.A single cutter with no balancing cutters to apply an equal torque opposite to the other, the mill was horrifically chattery. A simple test on scraps - A .005†depth of cut with the 10mm end mill on stainless was a nightmare, and .010†on aluminum was almost as bad. Trying the fastest RPM I could use to reduce the amount of material per rev removed, thus less torque did anything to improve the matter. Varied RPM testing didn’t improve results. The two bladed 16mm had less chatter, but was prone to the problem below. The insert immediately chipped on its first use.In addition, the extremely long shaft of the cutter meant that it stuck out 4†beyond the farthest amount I could get it into an R8 collet. The lack of rigidity made process even worse. I was tempted to cut it shorter, but not knowing the hardness of it and not wanting to ruin a good bandsaw blade or sketchily cutting it with an abrasive wheel I didn’t go for it. I’d rather just send this garbage back to whomever thought it was a good idea to sell it.
Jason and Kathryn
2025-01-17 16:05:54
the headline for the item suggests its for (side) end milling, and lists the angle of the cut is 90 degrees. It is in fact more like 85. It will leave ridges on the end face if you try to use it as an end mill, which was why I bought it. Nevertheless, considering the length of the tools, it's a good value for the money if you just want something to slot, shoulder and face mill, with good reach and the economy of using inserts. Runout was inside 0.001" on all 3 for me, so you could achieve decent accuracy for the operations mentioned, just not anything that requires the 90 degree side angle.
Guillermo Fuentes Orozco
2025-01-15 14:40:54
Llegó en excelentes condiciones. Recomiendo el producto.
Michael Keifenheim
2025-01-01 09:54:17
this is junk i was trying to cut some cold rollled steel and inserts kept breaking about .250 in the length of the cut depth of cut was .020 and only .025 in width while trying to side mill and i was using this on a grizzly G0781 mill so all feeds were done by hand
User
2024-11-12 10:31:30
Thread on the 10mm was stripped on arrival rendering it useless.Label on the 12mm tube is Weinaike BAP300R 12 1TC12 130.
Recommended Products
$24.04
$ 10 .99 $10.99