Your cart is empty.
Your cart is empty.The 36" Reusable Cavity Wand features a durable 360° spray tip to get in to hard to reach areas. This Cavity Wand attaches to the Cavity Coater Aerosol Can and is easy to clean and is engineered to require only an 1/8" hole eliminating the need to drill new holes.
Customer
2025-08-18 16:36:20
I’ve used this wand to get inside the door-cavities..., and other very hard to reach DEEP areas, where the conventional (red-straw-wands) that are limited to reach only certain areas,..(instead of pulling off the inside door panels)You have to be “very-careful†when inserting this wand, cause it tends to get stuck, or, it binds in some areas. the long tube may develop a “kink†eventually, and hopefully this won’t eventually end up breaking off,.?I ended-up “improvising†this spray-tube wand by inserting it into a (red-straw-wand) from another can of cosmoline-source, (when-new, clean & dry,..b-4 using the product) by applying “Hot-melt-glue†to the end of the wand butted-up to the spray nozzle with the red-spray straw inside intact to the nozzle. seal with the glue,..let cool-down,! It worked 4-me,! Sad,.. only this item works only on their products, and Not-universal to other spray-can sources!
Heather Abrahamson
2025-06-25 16:57:32
The Short hose means you need a lot of access holes to reach the whole frame, this could be in issue of you plan to use this on a unibody frame. Out of the box the house came with a kink that leaks slightly once straightened the tip is poorly secured & i Lost the tip in the frame rail when it snagged on something inside the rail on the second use (I hadn't even finished half of one frame rail) . Now it's stuck in there rattling around & i can't retrieve it because it's not magnetic.All this on top of the fact I thought I was also receiving the can of cavity coating. just a heads up, this is only a cap, hose & tip.
alm
2025-06-10 13:38:37
Perfect for what I needed
jake
2025-05-23 14:59:33
If you use this with surface shield cans, it will spray half out of the wand half all over your hands. To prevent this I added a small piece of heat shrink tubing over the little center tube in the head. It will crush down once you press it on the can like in the photo and give a good seal. Since I added that it hasnt leaked a drop.
Jacob Woods
2025-05-21 11:11:11
If you're planning on using this with Blaster Surface Shield, be prepared to get messy. It's going to leak out the cap and run all over the can. It does technically work, so if you're determined to get inside frame rails and tight spaces using aerosol cans, this is probably your best option. But for 30 bucks, I can't give this more than 3 stars. Creates a huge mess, wastes product, and overpriced for what it is, but gets the job done if you absolutely need it.
Jose
2025-04-19 17:06:06
My first impression: $20?! NO WAY!I had ordered it and planned on returning if I didn't use it. Well... turns out it ended up saving my undercoating project! If it wasn't for this wand, I would not have been able to spray inside my frame rails. I tried to use a wand that came with my WoolWax aerosol cans, and that thing SUCKED!This will work with any cans that have a female nozzle (pictured). This includes Fluid Film, WoolWax and PB Surface Shield! The WoolWax was SO high pressure it blew the wand that came with it straight out... but since this wand is attached directly to the nozzle, the pressure from pressing down with your finger to spray kept it in place! Well deserved review. Will keep for my next undercoating install.
Randy
2025-04-14 17:08:53
Someone on a forum said that Blaster recommended this product for applying theirs, that was a lie. This fits poorly and the majority of your product will come out of the nozzle area and cover your hands. I'm sure it works fine with KBS coatings products but don't bother with this if you're trying to apply Blaster Surface Shield.
D. Mckay
2025-04-11 12:23:00
Great hose and nozzle, no clogs as of yet and put 18 bottles of Fluid film though it. Just be warned that this is the hose and nozzle only, no can of cavity coat
gary s.
2025-03-18 11:35:12
works really good for car frame rails
Prof Mervyn Hyde
2025-02-27 15:53:26
The can is NOT included, as it says. So you are paying over $50 with shipping for a piece of plastic tubing and a small nozzle on one end and a spray can fitting on the other end that fits very, very few cans of cavity spray made these days, as it is the wrong type of fitting. In hindsight it is very poor value.
laurie priestley
2025-01-05 15:42:03
Misleading advertising photograph. Product is overpriced.
Recommended Products
