Your cart is empty.
Your cart is empty. Specification:
T Hand Ratchet Tap Wrench
Wrench Material: Alloy steel.
Tap Material: HSS (High Speed Steels).
Screw Type: Coarse thread.
Size of metric thread taps: M3*0.5, M4*0.7, M5*0.8, M6*1.0, M8*1.25.
Wrench body length: 85.5mm / 3.37inch.
T-Handle length: 99.9mm / 3.93inch.
Feature:
All-steel design with chromium-plated finish for the highest durability Beautifully precise ratcheting action for high quality work.
Easily switched from left to right handed operation, can also locked for non-ratcheting use.
T-handle is adjustable, T-shaped or 7 word shaped design, can one-hand operation, easy to use. The Handle made of high quality bearing steel, the chuck made of alloy steel.
Allows you to remove bronken screws or bolts.
Suitable for bicycle repair, assemble furniture, mechanical maintenance, ect.
Tap Wrench operate main point:
1. The good pit hole must chamfering chamfer first
2. To use drill clamp supporting tap
3. Tap to vertical alignment operation
4. Cut into rotation level 2-3 times
5. confirm vertical after Cut
6. Tapping 3/4 turn after a quarter back feeling
7. level reversal pull out after working
8. Remember that cutting metal need to use with the grease
Tips:
First install the power lever, which can be reversed in right-handed tapping or left-handed tapping.
After inserting the tap, set the toggle switch to the middle position to lock, then tighten the chuck clockwise.
Tighten the collet and use it, replacing different types of taps according to tolerance of the wrench.
When replacing the tap, rotate counterclockwise to release the chuck and adjust it to fit in the tread tap.
Be careful not to over-relax and loosen, which may cause the internal spring of the product to fall off.
Package Included:
5 x Screw Taps
1 x T-Handle Ratchet
Kyle K
2025-09-07 17:38:53
Bottle cage bolt rusted and snapped inside of my bike frame, so I needed to drill the hole out and tap new threads. This tool got the job done in a situation I was worried wasn't fixable, so I'm very happy with it. Obviously for $11 it's not the highest quality tool in the world, but it works in tight places, and the ratcheting mechanism is neat as well, I'd never seen a tap with that feature before.
charles
2025-08-04 10:34:57
works well for what it was intended
Chillehead
2025-06-04 11:28:08
Tap handle was of fair quality and included taps were rusty and of poor quality.
Randy Stepps
2025-04-08 10:51:36
Good product
Tim Murray
2025-03-30 19:55:30
One use, and it broke. To be fair, it actually broke on the third tap, but that third tap was within the same 20 minutes on the same piece of metal. Having said that, though, I was tapping M6x1 into existing M5x1 holes in an aluminum piece by hand--is there anything that should be easier? This kind of quality and longevity is inexcusable. I would not suggest buying this for your worst enemy. I recommend Amazon remove this junk from their inventory.
Sean
2025-03-27 16:09:58
I bought this thinking the racheting feature would be good. It is not. Tapping is usually a task of turning the tap some, backing off to clear chips, and then turning more.You can set this to the "middle" non-racheting setting, but my have kept slipping and switching on.If I had to do it again, I would get a simple tap handle.The chuck is fiddly as well, using knurled knobs that are hard to get tight.
William A Millinor
2025-02-23 16:20:36
I needed this for an M6 1.0 bolt hole that holds the headlight in a 1993 Mitsubishi Delica. It worked great for me and the headlight is now fully bolted in. I can't speak to the durability since I used one part one time but it did what I needed and the long handle was awesome for the fitment I needed.
Customer
2025-02-17 19:11:51
If you're tapping plastic or softer it seems to work fine (tested on pla), but it was not able to tap aluminum extrusion successfully. M5 tap made it about 3mm into a pre drilled hole before stopping and had stripped its thread on closer inspection.
AY
2025-02-08 14:50:09
It works as expected.
Recommended Products
