Your cart is empty.
Your cart is empty.Product Description
Titanium 1800° Spark Plug Wire Boots Heat Shield Protector Sleeve
Features:
1. The products are designed to protect your spark plug wire boots from the extreme heat
2. Constructed with double layered, they create an effective non-flammable thermal barrier that will extend the life of your ignition wires
Size
- Length:6"(15.5cm) ID:1"(22mm)
Color & Quantity:
Titanium * 8 PCS
Constitution:
Constructed with double layered
Part type:
1800°Spark Plug Wire Boots Heat Shield Protector Sleeve
Rated for 1800°F continuous use
2500°F intermittent Replacement for most spark plug boots even 90° "
Nanda Paranavithana
2025-08-26 15:49:02
Working well on my turbocharged 351W. The bull ring in the sock does limit what type of boots they will fit over so I extracted them.
Nicole
2025-08-11 11:40:40
Perfect, look new after 400 mile drive. I even spilled oil on one & was worried how that would go, they were fine, & cant see an oil stain or burn. I used needle nose pliers to open the rings a bit, slid the wires in, used the pliers to clamp the rings back closed (slight pressure) to hold them on the wires (boot) good. Was pretty easy, (20 minutes) and I have bigger wires than average. 2001 Silverado 2500HD 6.0L. (LQ4) With decent Duralast wires. (Larger wires than most). Tip: Be realaxed and comfortable, not irritated when installing, & it will go smooth.
Paul
2025-05-30 15:09:07
Easy to install and look good when installed. I checked the plug wire boot temperatures and they are much cooler with the boots installed. Hopefully this will stop the plug wire boots hardening and cracking over time from the significant radiated heat from my SS headers.
Vic-buyer
2025-04-25 12:54:27
Really good kinda on the cheap side of them but they look good ,kinda on the hard size to put on but that mean they won't come off lose too.
Michael Sanders
2025-04-09 18:40:38
Here’s how I got these over the plug wire boot.Insert a pair of pliers on the threaded side. Open the pliers to spread the jaws of the pliers inside the insulator. Rotate 45° and do it again.Now insert the boot inside the insulator.I used a pair of needle nose pliers to push the rubber into the boot inside the insulator.I used dielectric grease to coat inside the rubber boot allowing the boot to slide over the plug. I coated the coil side plug as well.The wires snap on easily even with the insulator over the boot.I’m very happy with this product and I’m glad they will protect the expensive plug wires.
Lawrence
2025-03-15 17:01:21
felt good. looked good. fit over granatelli wires and I did not snip the ring. Why? the ring is supposed to sit between the plug and the block (or close) so it never really moves. I put all of mine on without snipping that ring.2009 silverado LS 4.8 using E3 plugs and Granatelli wires.
GolferSA
2025-02-16 10:04:37
As others have said, these are very difficult to fit over a 90° boost on an 8mm spark plug wire. The stitching on the other end unraveled in less than a year.
Andrew
2025-01-07 14:59:49
So... I have Jegs 8.0mm wires on my SBC. Due to the header design I have both straight and 90 degree plug wires. Installation was simple and I did not experience any of the issues other discussed. There was no need to remove the metal ring or undo stitching. Seems like it will do a fine job protecting my wires from melting on the header.
Customer
2025-01-02 10:00:03
Easy to put on the sparkplug. Looks great too!
Rusty McNail
2024-12-08 17:15:38
I have received these but i have not installed them yet. Package came early and safe...good job all
lorna chapman
2024-11-25 21:24:16
Just what I wanted
Recommended Products