Your cart is empty.
Your cart is empty.Designed to Remove Gasket Residue from Steel and Aluminum Heads and Manifolds, Along with Carbon Build-Up and Even Rust. Can be used to clean disc brake caliper slides. Tungsten carbide tips are brazed to the steel blade that is molded into the comfortable 6" long handle.
John P
2025-09-07 11:26:12
I bought this set because I had heard good things about them when it came to removing old gasket material. I was working on a 1972 Honda CB500/4, and the side cover and head gaskets were near impossible to remove. I used a combination of brake cleaner, WD-40 and aircraft remover to loosen them up, and these to scrape down the gasket until it could be scraped off completely - you're not going to just be able to scrape the old gasket away, you have to work at it a bit, but I would say that when used in conjunction with the above liquids and an X-Acto knife, these scrapers DID shorten the job. They ARE very sharp though, and you have to let the tool do the work lest you gouge the aluminum - but you'll get the hang of it. Definitely worth having in the tool chest.
Paul E. Fox
2025-08-30 12:01:33
I've fought with paint scrapers, razor blades and mild steel scrapers to clean tough old dried-on gaskets off various sorts of metal. All were labor intensive and some risked damage to the surface. These things just work! You'll wonder why you waited so long to get a set.
Rob M
2025-08-29 15:33:30
Makes quick work on engine surfaces. Be very careful on aluminum because it will gouge if not careful.
B. Daniels
2025-08-11 15:16:56
I was trying to clean the thermostat and water pump mating surfaces from an older 1991 Jeep Wrangler. Needless to say, the gasket and antifreeze deposits were like built on metal and very difficult to scrape off. I used chemical gasket removers, acetone, wire brush and 3M green scrubber. I started to use a rotary tool, but stopped quickly as it can quickly remove metal and damage your surface. I decided to invest is these tools and they are perfect. You need both sizes to work different areas to minimize accidental damage because of bad angles or space constraints. These tools will scrape away those hard deposits, gaskets, etc leaving a nice smooth and flat surface. Take your time and don't rush and you will have a great surface to work with. I liked the handles quite a bit. Thick enough to fit comfortably in your hands. The product needs a case. There are covers for the blades, but no one would complain to have case. I bought a cheap case from Harbor Freight. The case had two permanent plastic partitions that I had to cut away using a dremel wheel. But the case fit perfectly.
Tonka
2025-07-27 13:16:04
This tool removes old gaskets like butter. You don't have to dig hard at all and it just scrapes the old stuff off.
LDJG
2025-07-25 14:19:23
I bought this set because I had borrowed a scraper (identical to the larger one in this set) and a truck ate it. I think it got wedged down along the frame-rail. It was gone forever, so I had to go shamefully tell my coworker that I had lost his prized scraper. He had bought it from a Matco tool truck about two months before and it was very popular for stripping paint off some of the heavy equipment we have to work with and fix up.I found this set of two for much less than my coworker had paid for a single one and I jumped at it. I wanted to replace his tool as soon as I could. I just hoped the quality would be up to snuff. A miracle happenned and when I pulled the scraper eating truck out into the parking lot later that week, the scraped came flying out. I was able to happily return the tool to my coworker the day before the new set arrived in the mail. Since we now had both of them, we have been comparing quality of the tools. The only difference between his Matco branded one and the larger one in this set is the actual word "Matco" stamped on the side. I literally think they are from the same factory. They are identical. The one from this set has worked just as well and been able to stand up to even more punishment. And this one comes with the smaller scraper for those hard to reach areas. The smaller one is also very high quality and durable.Wrap-up: Two scrapers that are just as durable as a nice name brand, but for way way less money. I have literally recommended these to all my coworkers who wanted the Matco version but thought it was way too expensive.
B Mysh
2025-07-01 11:32:56
Can't go wrong for the price, got myself one after using my co workers for a while.
TheBirdReviewer
2025-06-20 12:57:38
Helping a neighbor kid clean up his 40 year old Honda XL250R engine, old gasket material had been seemingly melded to the engine housing. Standard removal techniques weren't working, a flat screw driver was dangerous. This device is sharp, small enough, but simple enough to get the job done. It still took over an hour, but afterwards, the old material was gone and the surface was clean. Well worth it.
Craig
2025-06-14 16:12:20
This is the best tool I have found so far for removing old gasket material from engine parts. You do have to be careful to keep it flat or it can score the surface. Pushing it forward to scrap will score softer metals like aluminum. With this scraper and it's smaller brother, I no longer dread gasket removal.
AmandaMuir
2025-05-16 17:09:13
Some people say that a razor blade is good enough but trust me they have their flaws. These scrapers are a must have they stay sharp and will do anything you could ever want I use them on the bottom on engines to prep for sealant/ gaskets, and use them mainly on brake brackets as they get rusty quite often. Main reason I bought these from Amazon was they were half the price as mac and funny enough these are the same ones mac sells. I got 2 for the price of 1 and don't regret it. Awesome tools and better then changing razor blades all the time
MAES
2025-04-27 16:26:59
Nicely presented scrapers, machining of the carbide tips is a little inconsistent, slightly out of square on both tool tips. That said it doesn’t seem to affect the tools performance and the carbide tips have held their edge.Excellent job removing hard baked head, water pump, sump gaskets etc on older vintage components. These are instant time savers,comfortable quality plastic handles allowing less physical effort.
Customer
2025-02-08 12:27:09
I use these to scrape gaskets from engine surfaces. Be careful as they are sharp.
D Rob
2025-02-03 10:29:04
Quality product and quick shipping
Recommended Products
