Your cart is empty.
Your cart is empty.Product Description
Product Dimension
1: 1 Size design, same installation position, plug and play
Aluminum Lamp Cap
Aviation aluminum lamp cap design, non polarity, long service life
High Quality Chip
3020 high-quality chips, providing super bright light source output
Jstras
2025-08-24 09:28:29
These worked great! Super bright and dimmed smoothly to shut off. Have had other leds that have a choppy almost flashing dimming effect, not the case with these.Tried a different cheaper set of 567 led replacements for the liftgate door on my 2016 grand caravan but when installed it disabled my interior light system after the first time they were cycled. Of all the bulbs the single 567 was the only one that continued a low draw and stayed dim. With that bulb removed from circuit everything functioned normal. Since it was a 4 pk I tried a couple of them with same results.These have replaced the incandescent bulbs with zero negative side effects. Highly recommended
Patrick C.
2025-08-16 13:06:42
Perfect fit for my Chevy Cobalt LT 2010... Seconds to install and now my entire cabin lights up flawlessly!! No more dull warm yellow light that doesn't illuminate anything!!! Thank You!!!
Kimberly Smith
2025-07-13 13:31:45
Lights fit great and look great. I would buy again
Max
2025-07-08 12:28:45
Ordered a pair of these bulbs for the rear hatch area of my vehicle. I soldered them together and attached them to the overhead light fixture. It looks like daylight back there now. They don't heat up like the old bulbs did or cause the cover to warp. Really like the light output. Will use again when needed.
Scott Archel
2025-06-27 17:39:21
This is the brightest "direct" replacement for a 561 that I could find in warm white. The heat dissipation is excellent. It's basically a PCB printed onto aluminum, which helps the heat wick off really fast.The only problem is the end tabs on the LED board are not really a good direct fit for a 561 receptacle. This is mostly due to the fact that its about 1mm-1.5mm longer than an actual 561 halogen.My solution was to unsolder and put the end connectors on the other side of the board for a better fit. If you look at the pictures, you can see what I mean. With the end connectors on the same side of the board as the LEDs, usually part of the board hits the receptacle and you never really get to fully seat connectors securely. Sometimes when hitting a bump in the road, they will just slowly vibrate or pop out after a while. You can also bend the connectors backwards to give a bit more room, but I found that resoldering them to the reverse side gave a better result.
Daniel
2025-04-19 12:55:05
Excellent product and quality. Came on time.
Zezhile Hansen
2025-03-16 12:38:08
Wow. My car is now lit up enough to find things dropped on the floor.Love them.Thanks
Chad Hendrick
2025-03-15 15:39:00
Purchased these for the map lights in my 98 Chevy truck. They came well packaged at a great price. The bulbs seem very good quality and brightness? Oh yeah, they are insanely bright, just as I wanted. This was a great purchase!
Cali
2025-01-31 18:42:23
Very bright. I like
Ruloo
2025-01-27 18:58:24
Excelentes súper potentes para jeep xj 2000
Ryan C
2025-01-16 12:23:23
Nice and bright, plug and play, good fit. Good quality.
Joel
2024-12-15 12:24:52
Bought these for interior closet lights in our RV. Shipping was next day and they fit well. Very bright!.
cindy
2024-12-13 15:26:27
Put these into my old 80 Pontiac dome light and 95 Ford rear hatch light. So much brighter. Fit was good, quality was good, color was good. I would buy this again for anything this fits to.
Recommended Products