Your cart is empty.
Your cart is empty.
The briidea RV tank sensor monitor panel monitors gray, black, and fresh tanks, as well as your battery. This monitor tells you when it's full, at two-thirds, one-third, or empty. Allowing you to refill, empty, or clean your tank in a timely manner
Helen Cormier- Haga
2025-09-03 11:10:02
used it to set up a special tank for our jacuzzi tub to drain the water as we have a septic and it can't handle house and jacuzzi waste water. Great!!!
Cuz
2025-08-23 21:03:50
Ease of installation and use
Grace J
2025-08-15 09:00:22
Installed in my camper van build. I bought separate water sensors that I installed in the water tanks and it reads accurately! Super convenient. :)
Jeff Walker
2025-08-12 19:03:02
I have spent hours both with KIB tech AND with the Lukeman Youtube video trying to figure this thing out.1. The wiring diagram that comes with the unit is useless for actually wiring the monitor. And, the diagram shows wrong information: For example: The diagram shows a green wire going from the tank to the monitor. The only green wire on the tank terminates in a transistor and cannot be wired to the monitor.I am still waiting to hear back from tech on this one.The wiring is very confusing, even with the YouTube video. I still do not have a functioning monitor after HOURS of wiring the thing AND trouble-shooting as to WHY the tank monitor doesn't indicate the water level. Right now, the only thing it does is act as an expensive on/off switch for the water pump
Alejandro Cataldo Droguett
2025-08-05 11:56:30
Funciona bien
Bill
2025-07-13 15:48:51
Works well in my bus conversion. But I wasted time discovering the complete schematics why should the red wire connect to the brown one? See page two to understand.
Madeline Marcus
2025-05-31 13:24:42
Works as it should
Yepme
2025-05-16 17:26:08
Seems to work as intended.
Evin H.
2025-05-13 13:14:46
Just like the photo.Easy to install.Works great
Hang
2025-05-09 10:14:20
Product works but could be better. To check each tank you need to press and hold the button down. When you let go nothing lights up.
Helen Cormier- Haga
2025-05-04 10:49:02
used it to set up a special tank for our jacuzzi tub to drain the water as we have a septic and it can't handle house and jacuzzi waste water. Great!!!
Cuz
2025-04-15 16:17:29
Ease of installation and use
Grace J
2025-04-10 15:14:23
Installed in my camper van build. I bought separate water sensors that I installed in the water tanks and it reads accurately! Super convenient. :)
Jeff Walker
2025-04-01 10:15:12
I have spent hours both with KIB tech AND with the Lukeman Youtube video trying to figure this thing out.1. The wiring diagram that comes with the unit is useless for actually wiring the monitor. And, the diagram shows wrong information: For example: The diagram shows a green wire going from the tank to the monitor. The only green wire on the tank terminates in a transistor and cannot be wired to the monitor.I am still waiting to hear back from tech on this one.The wiring is very confusing, even with the YouTube video. I still do not have a functioning monitor after HOURS of wiring the thing AND trouble-shooting as to WHY the tank monitor doesn't indicate the water level. Right now, the only thing it does is act as an expensive on/off switch for the water pump
Alejandro Cataldo Droguett
2025-03-21 18:52:16
Funciona bien
Bill
2025-03-11 20:40:31
Works well in my bus conversion. But I wasted time discovering the complete schematics why should the red wire connect to the brown one? See page two to understand.
Madeline Marcus
2025-03-08 12:12:37
Works as it should
Yepme
2025-02-02 09:34:49
Seems to work as intended.
Evin H.
2025-01-30 10:24:17
Just like the photo.Easy to install.Works great
Hang
2024-12-12 18:14:44
Product works but could be better. To check each tank you need to press and hold the button down. When you let go nothing lights up.
Recommended Products
