Your cart is empty.
Your cart is empty.Product Description
MIXPOWER 6-Point 3/4-Inch Drive Deep Impact Socket- 33mm (Metric), CR-MO, 3/4-inch Drive 6 Point Axle Nut Socket for Easy Removal of Axle Shaft Nuts (33mm)
The MIXPOWER 3/4" Drive Deep Impact Socket- 33mm. Made from premium impact grade chrome molybdenum steel with black phosphate finish. This socket is radius corner design, 6-point opening reduces wear and increases torque on fasteners by placing force on fastener walls rather than fastener corners. Engineered for use with impact drivers. This axle nut socket can be used for installing, dismantling and repairing wheel or axle nuts on vehicles. The socket has high-contrast size marking that is permanently laser etched and easy to read, even in low light.
Size
- 3/4-Inch Drive-33mm (Metric)
Premium CR-MO
Made from premium impact grade chrome molybdenum steel with black phosphate finish.
Laser Marking
High-contrast size marking is permanently laser etched and easy to read, even in low light.
High-torque
Radius corner design, 6-point opening reduces wear and increases torque on fasteners by placing force on fastener walls rather than fastener corners.
Bonifay FL
2025-09-05 12:32:08
Worked great. Did not break under pressure.
Stephen Latino
2025-08-23 10:48:22
Works good , a little bit thicker than snap on
DeepDiver
2025-08-17 12:38:25
Seems well made. I only tested it to 185 ft-lbs. If you need more not sure.
Ben
2025-08-01 11:09:27
Thank you ðŸ‘
Downhill Diva
2025-07-31 16:49:56
Fit the 3/4†drive and the 42mm bolt, didn’t break, arrived on time.
Michael D.
2025-07-15 16:30:41
This is a tough 3/4" drive impact socket. For tough jobs where a lot of power is to be exerted.
MARC S.
2025-07-09 13:42:39
ðŸ‘
Dennis Elliott
2025-06-17 12:52:51
What can you say abouta socket. It's prettyJi
55
2025-06-08 14:50:36
I only use this on a torque wrench but it does the job fine
Tom Schoenherr
2025-06-02 21:54:36
Same as an expensive one only much cheaper
ivica stojcic
2025-05-23 10:34:26
perfect
Bonifay FL
2025-05-15 10:20:21
Worked great. Did not break under pressure.
Stephen Latino
2025-05-11 10:23:14
Works good , a little bit thicker than snap on
DeepDiver
2025-04-24 15:23:30
Seems well made. I only tested it to 185 ft-lbs. If you need more not sure.
Ben
2025-04-17 10:39:38
Thank you ðŸ‘
Downhill Diva
2025-04-12 18:25:15
Fit the 3/4†drive and the 42mm bolt, didn’t break, arrived on time.
Michael D.
2025-04-01 20:50:17
This is a tough 3/4" drive impact socket. For tough jobs where a lot of power is to be exerted.
MARC S.
2025-01-27 11:19:59
ðŸ‘
Dennis Elliott
2025-01-22 11:23:57
What can you say abouta socket. It's prettyJi
55
2025-01-17 13:13:28
I only use this on a torque wrench but it does the job fine
Tom Schoenherr
2024-12-27 13:41:51
Same as an expensive one only much cheaper
ivica stojcic
2024-12-26 11:11:41
perfect
Recommended Products