Your cart is empty.
Your cart is empty.Product Description
Perfect for home and retail shop
Use it everywhere, table top or wall mounted
Our label dispenser is the ideal tool for all small businesses, whether you're starting from your home or garage. It's where the journey begins. But even as your business grows, our product continues to streamline your labeling process. Whether you run a retail shop or an online business, you've found the perfect solution for your needs!
cldsk
2025-09-05 13:44:43
This is a nice label dispenser, well built. The label rolls I needed to dispense though only took up about half the space, so it was just too big for my purpose (labels for roomies to mark fridge/freezer items - so I didn’t have more labels to add).
Aja Drummon
2025-07-20 10:04:47
This has made my sticker collection so much more organized and made my life easier
Tabitha M.
2025-06-30 18:57:15
I used this to hold my genre labels for my library books. I'm going to order a 2nd one. It needs an additional separator, though. I tried to use a CD but the hole isn't big enough.
Liz Wengerd
2025-05-12 12:26:17
I use these stickers to package orders for my small business, and this sticker dispenser will be very helpful in keeping them organized. Especially when I add more stickers! You can also attach this sticker dispenser to your wall so it's not taking up your flat surface - very handy in my opinion!
cat
2025-04-13 10:23:53
I bought this label dispenser because it looked like it could also hold my spools of ribbon in addition to the use shown of holding labels and stickers. I was right! This dispenser works perfectly for my rolls of satin ribbon.Before this dispenser, ribbon spools were all over my desk on their sides. When you tried to make bows with the ribbon, the ribbon would fall off the desk and roll across the room. You would have to go chase the roll of ribbon down and put it on your lap – only to have it happen all over again. Now I can pull the ribbon I need from the dispenser. The dispenser doubles as an extra set of hands to hold the ribbon while I make bows. Aha! It is a perfect additional use for this dispenser.I really like the individual clear plastic acrylic discs. They took care to keep the thin layer on top so you could peel them when you received the dispenser. This alleviates the amount of scratches the acrylic could get in transit. I really liked this.If the dispenser didn’t hold the ribbon and I was unable to use it with ribbon, I did have rolls of labels I could use it with. I pulled off the ribbon to see how well I liked using it with my rolls of Christmas labels and stickers. I convinced myself that I needed to buy a second one for my labels.They provide hardware if you want to hang it on your wall. I chose to keep mine on my desktop.Super simple to assemble. Took five minutes to put together – if even that.5 out of 5 stars. I need to purchase a second dispenser for my rolls of labels and stickers.Title of the item I am reviewing:Multi-Use Large Label Dispenser for Rolls of Sticker Labels - 11.8"x6.7"x5.5", Heavy-Duty, Wall-Mountable Acrylic Sticker Roll Dispenser, Anti-Slip (7 Disks/Brown)
Bix
2025-03-29 14:01:40
This label dispenser can sit on a table or be mounted on a wall. It comes with rubber feet on it making it nearly impossible to slide. It also comes pre-drilled to hang on a wall, with the hardware needed to mount it too. The plastic rings used to separate rolls are independent and can all be used, or just a few. They slip on over the end of the plastic roller bar. Nice dispenser.
Donald Shockley
2025-02-27 17:08:26
This is a bit larger than I need for the relatively few small rolls of labels I am currently using. But better to have the room for larger rolls and not need it than to need it and not have it later. And doing a test layout with smaller rolls I am currently using, if I get more rolls of the same size, the provided dividers will be enough to fill the full width.Although the holder works well as designed and shown in the listing photos, one idea I had prior to ordering did not work out. I had hoped that if I changed the feed route of the strips, different from the listing photos, I could get the labels to start coming off the backer for easier removal. Going under the top rear rod, over the top front rod, and behind the bottom rod does bend the understrip sharply, it's not enough for the edge of the sticker to lift off like I hoped it would. It's still easier to peel off than the flat strip, but not as much as I hoped.Those support rods were the one area of difficulty I had. Upon receipt, a couple rods were loose because the screws had come off the end. But when I tried to put it back together, the sides were distorting. But when I loosened them back up, the rods were flopping around in the holes. After much fiddling trying to get the screws "just right" and failing, I took it all apart to investigate. After measuring I found 2 causes, one easily fixed but the other not so much.The rod holes on one side were slightly too small, but not so small as to fit the screws only. This was what was causing the flopping when loosened, small screw shafts in almost large enough rod holes. Drilling out the holes a bit (with drill in reverse to prevent splitting the plastic if the bit grabs in forward) solved that issue.The second issue was that the rods themselves are the wrong length for the sides. The rods just barely reach the holes on either side. The outside width of the plastic body was 304mm, and the inside width was 298.5mm. All the rods were 300mm. That's why the sides tried to bow in when I tightened the screws to pull the rod into the holes. The rod should either be 298mm to fit inside with just screws in smaller holes holding the sides against the rods. Or 304mm with rod sized holes, and the screws stopping the rod from sliding out. But a 300mm rod and an inside width of 298.5mm leaves just 0.75mm on each end of the rod supported by the larger holes. It took a lot of fine adjustment of the screws, and loctite to keep them there, before both ends of the rods would stay in the holes.
Customer
2025-02-14 16:15:35
Works OK for dispensing labels but the separators don't fit the spool. They are too small.
Recommended Products