Your cart is empty.
Your cart is empty.Product Description
High Torgue&Low Resistance
German tech bearings, low self-inductive reactance, good responsivenes, longer life and low working temperature.
Low resistanse enables good thermal conductivity. It will work at a safe temperature.
Low Noise
The internal rotor of stepper motor adopts German tech. And the surface is coated with imported rotor glue to prevent the burr on the surface caused by the oxidative grinding of carbon steel that cause the motor noise.
ES
2025-08-10 11:07:13
I had a resin spill on my Halot One Plus resin printer that got into my Z-axis motor, locking it up.I ordered this set of 3, because it was the only 42-48 stepper motor that I could find with fast delivery.This motor was exactly the right replacement. The size was obviously correct, and the old motor was wired exactly the same as this motor. I just had to plug it in and it worked perfectly.I wish that I didn’t have to buy three of them, but I suppose I’m covered in case I have another spill.If you’re looking to replace the motor in a Halot One Plus printer, this is exactly the one that you want.
JK
2025-07-29 13:12:32
This worked as a replacement for an ANET A8. However, the wire order was reversed. Needed red, blue, etc., top down so had to change that. I couldn't get the sockets out of the JST connector so just cut it off and soldered the wires to the old connector. Motor working just fine, calibration cube was PERFECT so e-steps didn't even change.
Wiltonh
2025-07-12 11:13:00
The stepper on the bed of my A8 died. It was so stiff you could almost not turn the shaft by hand. I purchased this stepper and it was an exact fit.Make sure you check the number of steps per degree of rotation so you get one that is exactly the same as your original.
CMSemp
2025-07-02 11:01:22
Perfect replacement for the Halot one 42-48 motor. No rewiring, just plug and play. Multiple prints with no issues. Would have been nice to have purchased just one motor instead of three, but will have spares incase a vat leak claims another motor.
Justin Clopp
2025-06-29 21:24:22
Does not work with my Anycubic Kobra Go like I was told it would. It's to big. Really irritating!
J. Zenkus
2025-06-28 15:11:53
If you hooked this up and your motor is just pulsing, keep in mind not every manufacturer uses the same wiring scheme. Every stepper motor has a A/B/C/D order.. Find out what order your printer uses and make sure the wiring order matches. I find that it's easier if you use the included connector, cut your existing wiring and solder it in the right order. google image search for instance "anycubic stepper motor pinout"
MM
2025-06-22 11:02:00
Drop in replacement for Tevo Tornado Y axis. Works perfect. Don't overtighten the belt as that will just wear out the bearings faster. Also, dial down (way down) the JERK and ACCELERATION values to keep the mechanical stresses lower and eliminate layer shifts. Great product... will buy from them again in the future as necessary.
Customer
2025-06-07 16:47:26
3 stepper motors for 6.99! What a great bargain. Thanks to the seller for being reasonable and realistic about the value of these motors
Randy
2025-05-16 10:47:40
This product, 5mm brass rods, brass couplers, a stepper motor driver and controller were all bought together for a science project we were working on. The mounting holes in the motor are M3. I didn't want to buy a couple of dozen of M3 screws so was looking around for some screws that have M3 thread. If your into building your own computers or have a scrap one around the house a lot of the motherboard and auxiliary cards have exactly M3 screws. . So pleased, thanks Amazon, thanks seller, Definitely recommend
Mabi
2025-05-12 12:36:57
Works as expected. Easy to connect - a straight connection with the original cable. The cable that comes with the motor is rather thin, but the original cable works.
King Star King
2025-05-03 12:18:57
Los motores sirven excelentemente, pero lamentablemente los cables venÃan conectados de forma errónea lo cual hacia que pareciera que no funcionarán los motores pero los proble con otros cables que tenÃa y ya funcionaron, dejo foto del cableado correcto.
Samuel Ochoa Cortes
2025-04-23 14:08:44
The media could not be loaded.
cust:
2025-02-10 11:54:19
items are as expected, functional
Recommended Products
$24.99
$ 11 .99 $11.99