Your cart is empty.
Your cart is empty.Product Description
Feature:
- 100% brand new and high quality
- Speed, fuel, total mileage, adjustable mileage
- With driving instructions, a clear display, engine failure warning lights
Technical Specifications:
- Supply voltage: DC 8-12V
- Speed display: km / h, mph
- Speed display range: 0-199km / h (mile)
- Odometer display: 0 ～ 999999 km (mile)
- Odometer display unit: 0.1km
- Odometer display range: 999.9 kilometers (miles)
- Daily odometer display unit: 0.1 km
Suggestions:
- Installation is simple, but professional installation is always recommended.
- Due to manual measurement, the real size may have some errors with the data, thanks for your understanding.
J.R. SANCHEZ
2025-09-03 12:38:18
Looks great and all but the instructions need to be a bit more clear. As well the sellers to be more specific on what bike it can go. Just to pull it on my suzuki katana 93 I need to do a lot more plug and play. I gave it to a friend and worked perfect for him since he had a newer motorcycle
Andrew F.
2025-06-14 18:13:01
The media could not be loaded.
QSmooth
2025-06-02 17:00:19
I read other reviews before buying. The person who left the one star just assumed color instead of looking at instructions. The black wire (12v ignition) turns on and off the speedometer. The red (12v constant) is for the clock memory. If the red wire gets disconnected the clock goes back to 00:00 AM.INSTRUCTIONS: It does come with instructions but not very helpfulLeft signal, right signal, and high beam is easy to figure out.RPM WIRE: Tap into CDI signal wireFUEL SIGNAL WIRE:I did my own research on the fuel level because not much documents were on the internet.Full: 0-11 ohms80%: 12-32 ohms60%: 33-50 ohms40%: 51-68 ohms20%: 69-87 ohmsEmpty: 88ohms or aboveDisconnected: fuel gauge doesn’t appearBELOW ARE FUEL SENDERS THAT AMAZON SELL:Gy6 fuel sender (old Hondas)(3 wires): Ohms are way off. Up to 600 ohms240-33 ohm fuel sender: Correct direction (full/empty) but not right ohms0-190 ohm fuel sender: Wrong direction. Full/empty swapped. And wrong ohm.0-90 ohm fuel sender: Correct ohm but wrong direction. You can use this but you might have to install it at the bottom of the tank. Install it upside down to get the correct fuel reading.TEMP SENSOR: Your temp sensor needs to be in the same ohm range. 699 ohms (cool) - 82 ohm (hot)FINAL THOUGHTS:It’s $50. It’s cheap. My original TaoTao atm50 Pony’s speedometer is $30. And to change out all the light bulbs to LED would’ve cost more.If you don’t use any of the wires it simple doesn’t appear. I have a scooter. It doesn’t have gears like motorcycle. The gear number does not appear on the speedometerFuel gauge gave me the most trouble. Might be easier to go with an external fuel gaugeCondensation does allow moisture into the display. There is a hole to allow air in and out. But that hole hurts more than it helps
Ken Osbun
2025-05-12 18:01:45
There is no adjustment at all for OHM resistance so that the temperature or fuel gauge report correctly. There is not enough adjustment in the number of magnets or size of tire to use OEM speed sensor, you are required to install the provided speed sensor. If the sun rises that day, you will not be able to see the screen due to the glare from the screen covering. The turn signal indicators did work, so there's that...
Joe
2025-04-27 10:54:17
Quality is pretty good. However the screen is not very good. An only see it from certain angles. And there is no way to calibrate the speedometer as far as I know
Kari Kapavik
2025-04-15 11:25:13
used this to upgrade my GTI jetski to full digital panel. worked GREAT. even speedo worked. used the original magnetic impeller and just used 4200 to glue the pickup right above the original pickup, wala.. i got speed. i had to set the pickup to 8 magnets and 30cm or something like that.. smallest i could get it, then just adjusted the mag counter until the speed was right. wala. also used temp sensor on the water output from the engine, and the tach went right to the origanal tach line. check engine light works in reverse for seadoo, so with this thing, light on is a good thing. i also use my jetski's in salt water, and this thing is still going strong.. no water leaks at all.. and trust me when i say this, because i get it VERY WET.. i mean, i've had this thing 3 to 5 feet under water several times per trip.
Chris IRL
2025-04-04 15:38:34
advertised as suiting 1 2 sand 4 cyl and only has options for 2 and 4
José Velez
2025-03-31 14:42:34
Tres años usándolo y perfecto a pesar de que le entra el agua cuado hay fuerte lluvia
Kaven vachon
2025-02-19 16:53:39
Fonctionne à merveille
Joey
2025-01-02 10:29:04
Nice screen, works great at first. Screen isn’t enough bright for full sun but not that big of a problem. The main problem is water went in the screen. No, there’s no seal damage so i dont know how it happened but in Quebec cold morning, water stay in the screen till noon. Since there’s water in the screen, short circuit look to happen also sometimes screen just reset or show wrong things and start working good again at noon… And when you installed it and cut the wires, theres no return so… I dont know how to reach out the seller but i hope he will reply to this.
Recommended Products