McMaui
2025-08-20 14:31:09
This product was easy to install and even easier but to use. Really like the paddle storage that is integrated into the rack, and how easy it is to store and remove my wife’s SUP. When not in use the rack can be turned so it is flush against the wall. Great simple design.
Jerry Thompson
2025-08-18 10:58:20
The supports are “first class†and easily support my 12’ board. I particularly like the hinged action that allows me to swing the supports out of the way when the board isn’t on them. The reason for my 4 star review in lieu of 5 is because of the supplied screws that immediately striped. I recommend using quality screws and toss the supplied ones. I used exterior deck screws w/star heads (they seldom ever strip).
Mpg
2025-07-24 12:59:24
Look at unit carefully before installing to get retainer anchors in the correct position. Otherwise easy to install. Unit seems very sturdy.
Moonglow ColorKid
2025-07-14 14:02:54
Well made rack, very simple to put up and capable of holding our board very securely. Installation took less than 20 minutes and despite being pretty lightweight the rack can hold our very large paddle board with no issues. Well, there is the issue of getting it up into the rack, but that's our issue and not a problem with the rack itself.The frame and hardware are very solid and the attached protective pieces help prevent scratches to your paddle board. It's a nice step up from trying to balance it on top of the boards we have stacked on our lumber racks, so for 50 bucks I'd definitely suggest it to anyone who could use a little extra space in their garage! Recommended.
Lemon
2025-06-04 17:50:30
A very solidly built rack that is perfect for my SUP. Padded and heavy duty, installed easily.
TD
2025-03-29 20:34:06
The hooks are too narrow to fit a standard 6†thick SUP. My board only fits half way on. The screws provided are junk- I snapped three of them trying to screw into studs. The stud mounts are horizontal so it’s impossible hard to hit a stud with both screws unless you screw them in at an angle. Poor overall design.
Mad Max
2025-03-13 15:26:48
-This is a good rack design. It's an upgrade from bungee cording it to the wall, though I'm not totally convinced it's worth the cost.-For people who say their board doesn't fit, you may have to move the brackets closer together. It may just be an issue of the board shape at the nose / bow.-Do not use the included screws. I used deck screws instead.-Install is easy and straightforward.-The two best features - first, the brackets are tall enough that the board doesn't lean, it holds the board flush against the wall. Second, the brackets fold flat when not in use.-The only suggestion I have - make the brackets expandable, so you can adjust to hold two boards.
Heather
2025-03-08 18:58:55
Waste of money. Held up for a little then my paddle board fell off the hooks. Hooks broke and came apart. Leaving my paddle board damaged.
Danielle
2025-02-21 11:39:03
Super easy to install, and they swivel against the wall if you don't want them sticking out, when not in use. The only down fault to that is they swivel a bit when your trying to put your paddle board on the rack (I found anyways) but I'd definitely recommend, best bang for your buck! I was hesitant to buy because some said there board didn't fit but I can't see how their board wouldn't fit its super spacious and my board is 3" thick... with lots of room!
Garry Valin
2025-02-12 18:00:17
Good racks. Hold the boards snug to the wall. Works as expected
Rexana Stickwood
2025-01-05 10:18:01
This has been a game changer for storing my board. I have a 10'6 epoxy board with no open space to store. It was easy to install and I love the the bars lay flat against the wall when the board is in use.
Thanks
2025-01-03 11:11:14
Product as described can be trusted. Thanks
Graham Mino
2024-12-24 13:12:17
These are great, for us, we had to put the first one about 18" from the floor as we have installed two of these, and the higher you go the trickier the higher one is for finessing out of the rack. Also, ensure you have a perfectly fitting Phillips driver bit and lean into it, the screws are long and need to be pushed into a stud, pilot holes help.