Your cart is empty.
Your cart is empty. Packing list:
1. Main mounting bracket 1pcs(3 mm thick high quality aluminum)
2. Clamp V Jaw Bracket 2pcs（Stainless Steel）
3. U-Bolt 2pcs （Stainless Steel）
4. Nuts 4pcs （Stainless Steel）
5. Spring washers 4pcs （Stainless Steel）
6. Plain washers 4pcs （Stainless Steel）
B Brennan
2025-09-02 16:59:41
I like the multi step clamp that works with different sized poles. One by itself was a little flimsy for the weather station. Two clamps made it rock solid. The other pair is for a VHF/UHF antenna using TV antenna mast poles. The mounted pole rests on an oak board to support the weight. The clamps provide stability. I added 2x4s to the shed wall for both installations. This provided good screw spacing.The only recommended improvement would be stronger bracing. All materials are high quality.Do not drop a nut in gravel!
GranDoc
2025-08-16 10:22:34
I used this mount on the siding of my house at the eave to support the mid-section (1 1/2" diameter section) of a telescoping fiberglass antenna mast. This avoids the need to raise the mast out away from the house the guy wires/ropes, and the mast is held firmly. The mount is well-made with appropriate gauge metal to withstand strong forces. The base plate (mounted on the wall/house) has a versatile pattern of holes to allow most any geometry required. The antenna mount is a very standard double U-bolt that cinches down on two cross bars which have a jagged circular inner pattern to appropriately grip the attached mast to and prohibit any rotation. All hardware is included except for whatever items you need to actually screw the baseplate to the wall -- you supply that based on your installation needs.
Justin Wilson
2025-07-26 16:20:22
I used this to mount a wireless Internet bridge between my house and garage. Works great. Lots of mounting holes to get that great angle.
Michael D. Miller
2025-07-15 15:50:27
I ordered this bracket because it would weather well without rusting. However, being the bracket itself was aluminum I had reservations about its strength given my application. My mast is 5 feet tall with a large antenna with a 4 foot spread. The bracket failed with a 40mph wind gust. But I unbent the bracket to its original position and added a diagonal brace to my mast to prevent another failure. So far so good! If bracket was formed with material half again thicker I believe it was be a great value for most applications.
PHP - ALABAMA
2025-05-25 14:23:22
This pole mount support was used to mount a back plane that a solar cell and Mesh tactic transceiver were mounted on. The support has survived severe weather including 50+ mph wind bursts :0). The material quality and workmanship is top notch.
William Armstrong
2025-05-20 10:48:22
These clamps are holding up a twenty foot antenna mast and holds it in place very well.
fminix
2025-05-14 12:46:55
These brackets are made of sturdy aluminum with stainless steel hardware. As a result, there are no worries about corrosion and rust stains on my white wall. I used these brackets to support a pole holding a Starlink Mini. It is perfect for that application and installation was very easy.
Mojo
2025-03-29 18:05:57
This worked great for me to mount a water well teleswitch antenna. I flipped the bracket so I used the star pattern to mount the antenna connector.
Jorge Tijerina
2025-03-16 18:02:24
Sirve para lo que la compre
Dirk Gäding
2025-03-09 12:51:51
muito bem brigado
AndréK
2025-02-04 15:08:15
Hält gut. Hab aber auch nur ne leichte Kamera dran. Denk aber das es ach mehr ab kann.
Recommended Products
